TURFCO 85874 Скачать руководство пользователя

Страница: 10 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

DRIVING THE MACHINE

(See Figures 3, 4 and 5)

To begin your driving lesson you will

need a large smooth paved level area

like a parking lot.

Forward and Reverse Operation

(See Figure 3)

1. Stand on the operators platform

before touching anything. Do No

stand on the yellow pedal.

2. Place one hand on the support bar

and grip the steering wheel with the

other hand.

3. Release the Parking Brake.
4. Using the hand on the support

bar, move the speed control lever

slowly

towards the support bar.

The machine should move ahead

slowly. Slowly moving the speed

control bar closer to the support bar

will increase the forward speed.

5. The machine has a braking system in

the transmission that automatically

stops the machine when the speed

control is released. Let go of the speed control and it will

go to neutral applying the brake. The machine will quickly

come to a full stop in just a few feet of travel. Try this

many times to get used to the braking action.
● Go ahead slowly and release the speed control lever.

The control will return to the neutral position and the

machine will stop.

The machine will stop quickly.

● You may speed up a little as you become more

accustomed to the start and stop characteristics of the

machine. Continue this for several minutes gradually

getting more speed and becoming used to the stopping

motion.

● Also try the same movement using the reverse lever on

the left side.

6. The reverse speed control is under the left side support

bar. Move the reverse speed control upward toward

the support bar

slowly

. The machine will slowly start

moving in reverse. Try this a few times to get used to the

movement and control.

Using Forward Speed Control Pedal

(See Figure 4)

The T3000i Applicator has a “Forward Speed Control Pedal”.

This pedal can be used to control forward speed, the same as

the forward speed control handles. This allows the operator

to use his hand to operate the other spreader and sprayer

controls on the machine.

FORWARD/REVERSE

SPEED CONTROLS

FORWARD

REVERSE

OP85872-09

SUPPORT BAR

FIGURE 3

PARKING

BRAKE

OFF

YELLOW

FORWARD

SPEED

CONTROL

PEDAL

FORWARD/REVERSE

SPEED CONTROLS

FIGURE 4

OP85872-07

FORWARD

SPEED

CONTROL

FORWARD

REVERSE

OPERATION

Содержание 85874










































Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды

TURFCO 85874, Руководство оператора

Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды