TURFCO 85874 Скачать руководство пользователя

Страница: 14 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

THE SPREADER

The spreader has several components and controls you should be familiar with before operating the machine.

1. HOPPER

(See Figure 8) -

The spreader hopper size is 2.9 cubic feet and holds 175 pounds (0.08 Cubic Meter/

79.4 Kg.) of material.

2. SPREADER GATE

(See

Figure 8) -

The Spreader

Gate opens allowing the

material from the hopper

to fall onto the spinner

wheel for spreading. The

gate is operated from

Spreader Gate Open/

Close Control lever on

the right side of the

operators control.

3. SPREADER GATE RATE

ADJUSTER DIAL

(See

Figure 9) -

The Spreader

Gate Rate Adjuster Dial,

is a round white plastic

cam on the front of the

spreader hopper. This

cam sets the exact

opening of the spreader

gate.

The exact setting

for the gate dial should

only be set by licensed

persons.

4. “ACCUWAY” SPREAD

PATTERN ADJUSTER

(See Figure 9) -

The Spread Pattern Adjuster moves the position of a black plastic wedge that is under the

hopper gate opening. When the gate is opened, the wedge controls where the material lands on the spinner

wheel. This affects how fast the material exits the spinner wheel and changes the throw of the material. The

wedge can be adjusted to throw more material to the right, more to the left, or an equal right to left pattern.

More detailed information about

the adjuster can be found in the

spreader calibration section of

this manual

The Accuway Spread Pattern

Adjuster must be readjusted if

the Spreader Gate Rate Adjuster

Dial has been changed or when

a different product is being used.

Consult the calibration section

in this manual for proper

adjustment.

“ACCUWAY”

SPREAD PATTERN

ADJUSTER

SPREADER

GATE RATE

ADJUSTER

DIAL

TRIM SPREAD

BOARDER

PATROL

DEFLECTOR

OP85872-21

SPREADER

SPINNER

WHEEL

FIGURE 9

SPREADER SPINNER

WHEEL AND SHAFT

PULL PINS

OPERATION

TRIM

SPREAD

BOARDER

PATROL

CONTROL

TRIM

SPREAD

BOARDER

PATROL

DEFLECTOR

SPREADER

HOPPER

SPREADER GATE

OPEN/CLOSE CONTROL

OP85872-13

SPINNER SPEED

CONTROL

SPREADER

SPINNER

WHEEL

FIGURE 8

SPREADER

GATE

Содержание 85874










































Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды

TURFCO 85874, Руководство оператора

Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды