TURFCO 85874 Скачать руководство пользователя

Страница: 3 / 41

85874 & 85875 Rev C

TURFCO T3000i SERIES APPLICATOR

SPECIFICATIONS

Registered Trade Mark and Patents

US Patent 8,056,828 - Additional Patent Pending

TURFCO

is a registered trademarks of Turfco Manufacturing, Inc.

T3000i™ and

VARI-RATE™ are trademarks of Turfco Manufacturing, Inc.

SPYKER, ACCUWAY, and BORDER PATROL trademarks of Spyker Spreaders, Brinly-Hardy, Inc.

DELAVAN

is a trademark of Delavan Pumps Inc. - AQUATEC™ is a trademark of AquaTec International, Inc.

BRIGGS AND STRATTON

is a registered trademark of Briggs and Stratton Corporation. Inc.

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING

Specifications

Dimensions:

Width

..........................................................

35.5” Inches (0.90 Meter)

Height

.........................................................

50” Inches (1.27 Meter)

Length

........................................................

65” Inches (1.65 Meter)

Weight Empty

...................................................

500 Pounds (227 Kg)

Weight Loaded

Spreader Full, Sprayer Tanks Empty

..........

675 Pounds (306 Kg) With Hopper Extension

Spreader Empty, Sprayer Tanks Full

..........

635 Pounds (288 Kg)

Spreader Full, Sprayer Tanks Full

..............

810 Pounds (367 Kg) With Hopper Extension

Operator Controls

Steering and Drive

...........................

Forward/Reverse Speed Control, Engine Throttle, Forward

Speed Control Pedal, Parking Brake and Freewheel Lever

Spreader

..........................................

Spreader Gate Open/Close, Vari-Rate Adjuster, Spinner

Speed Wide/Narrow, Trim Spread Border Control, Accuway

Spread Pattern Adjuster, and Gate Calibration Dial.

Sprayer

............................................

Full Width On/Off, Trim Width On/Off, Hand

Gun On/Off, and Spray Pressure Adjustment.

Production Rates

Spreading and/or Spraying

..................

4,000 Sq. Ft./Minute - 240,000 Sq. Ft./Hour

(371.6 Sq. Meters/Minute - 22,296 Sq. Meters/Hour)

Spreader Hopper Capacity

......................

Approximately 2.9 Cubic Feet - 175 Pounds

(0.08 Cubic Meter - 79.4 Kg.) with Hopper Extension

Minimum/Maximum Spread Width

Full Spread

..........................................

18’ to 22’ Feet (5.49 to 6.7 Meter)

Trim Spread

.........................................

12’ to 14 Feet (3.66 to 4.27 Meter)

Sprayer Tank Capacity

.............................

16 US Gallons - 135 Pounds (8 gallons per tank)

(60.57 Liter - 61.3 Kg)

Minimum/Maximum Spray Width

Full Spray

............................................

9’ to 11’ Feet (2.74 to 3.35 Meter) 9’ Effective

Trim Spray

...........................................

3’ to 4’ Feet (0.91 to 1.22 Meter)

Engine

........................................................

Briggs and Stratton INTEK 10.5 HP (7.8 kW), with 16 amp

Electric Voltage Regulator. Optional Electric Start Kit For

85874, Electric Start Standard For 85875.

Fuel Tank Capacity

...................................

2 Gallons (7.57 liters)

Transaxle

...................................................

Variable Speed with Brake and Freewheel Control

Tires

........................................................

Front - 13 x 6.50-6 Rear - 18 x 6.50-8

Maximum Transport or Operating Ground Speed

..........

5 MPH (8.04 Km/h)

Turning (Steering)

..............................................................

9 Foot Circle (4.5 ft radius)

Maximum Slope Angle of Operation

...............................

15° Degrees

OPERATE ONLY IN AREAS WITH ADEQUATE VENTILATION. DO NOT OPERATE ENGINE IN ENCLOSED AREAS.

Содержание 85874










































Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды

TURFCO 85874, Руководство оператора

Результаты поиска

Содержание 85874

Отзывы:

Похожие инструкции для 85874

Бренды по названию

Популярные бренды