TURFCO 85804 Скачать руководство пользователя

Страница: 23 / 68

OPERATION

SETTING CONTROLS FOR LIGHTSPREAD OR

HEAVYSPREAD OPERATIONS

(See Figure 13)

Changes to the settings of the spinner speed control,

the metering gate, spinner diverter, spinner wheel vane

mounting angles, and the conveyor belt speed control

are required when changing between Lightspread and

Heavyspread top dressing operations. See steps in

Figure 13.

TO AVOID SERIOUS INJURY,

Always Stop the Engine Before Making Any

Lightspread/Heavyspread Adjustments.

SETTING WIDE

SPIN

1530 METERING GATE

(See Figure 13)

The metering gate opening

size is controlled in two

calibrations, Lightspread and

Heavyspread. The metering

gate stop pull pin on the side

of the metering gate mount

must be pulled out to allow

the metering gate to be moved

into the larger opening size for Heavyspread.
Use the following settings for Lightspread and

Heavyspread operations -

LIGHTSPREAD -

Set metering gate in zones “A”

thru “D”.

HEAVYSPREAD -

Pull metering gate stop pin and

set gate in zones “E” thru “H”.

The marks on the decal are for reference only, they do

not represent any measured amounts of top dressing

material.
Because moisture content and varying weights of top

dressing can effect the ﬂow of material thru the metering

gate, adjustments may be needed to maintain an equal

distribution and an even spread pattern.
If the amount of material being deposited on the spinner

assembly needs to be corrected, adjust the metering

gate opening. To increase the volume of top dressing

material, increasing the metering gate opening will have

better spreading results than increasing the conveyor

belt speed. For less volume of top dressing material,

decreasing the metering gate opening will have better

results than decreasing the speed of the conveyor belt

SETTING WIDE

SPIN

1530 SPINNER HYDRAULIC

SPEED CONTROL

(See Figure 13)

The speed control varies

the speed of the spinner

wheels. Increasing the

speed increases the

spread width, decreasing

narrows

the

width.

Changing the speed does

not effect the volume of

material being spread,

however, the thickness of application will change as the

spread changes.
Use the following speed settings for Lightspread or

Heavyspread operations -

LIGHTSPREAD -

Set and lock the spinner speed

control at “4”.

HEAVYSPREAD -

Set and lock the spinner speed

control at “3 or less”.

In the Heavyspread setting, the speed control should

be at 3 or less. Do Not exceed 3 during Heavyspread

operation, limit any changes to setting the control to

under 3 along with changes to the conveyor speed

control or the metering gate setting.
Moisture content and the type of top dressing material are

variables that will affect the setting of the speed control.

Use a slower setting for dry top dressing material that

ﬂows easily. Increase setting to handle heavier types of

top dressing or to increase the spread range. Increasing

the speed will broadcast the top dressing over a larger

area. Experimentation by the operator will help to

determine the proper setting. The spinner speed control

does not effect or change the speed of the conveyor

belt.

SETTING HEAVYSPREAD DIVERTER

(See Figure 13 and Figure 14)

The Heavyspread Diverter changes the spread pattern

during Heavyspread operation. For Heavyspread, the

diverter should be in the lowered position and securely

locked with the diverter locking knob. During light spread

application, the diverter should be locked in the raised

position.

WARNING

��

B C

OP85804-02

OP85804-03

FIGURE 14

LIGHT

HEAVY

DIVERTER

LOCKING KNOB

DOWN FOR

HEAVYSPREAD

UP FOR

LIGHTSPREAD

OP85804-04

Содержание 85804





































































Результаты поиска

Содержание 85804

Отзывы:

Похожие инструкции для 85804

Бренды по названию

Популярные бренды

TURFCO 85804, Руководство оператора

Результаты поиска

Содержание 85804

Отзывы:

Похожие инструкции для 85804

Бренды по названию

Популярные бренды