background image

This form must be completed in its entirety and submitted to TurboChef to activate the warranty and ensure 

proper operation. In the case of a multiple oven installation, a “Start-Up Checklist” form must be completed 

for 

each oven

, noting its position in the stacked con

fi

 guration. 

-Scanning/emailing to: [email protected] 
-Mailing to: TurboChef 

 

      Attn: Warranty Department

 

      4240 International Parkway Suite #105 

 

      Carrollton, TX 75007

-Faxing to: 214-379-6085

Before attempting to install the oven, ensure all utilities are complete and ready for 

fi

 nal connection and 

operation. If any of the requirements listed below are incomplete, notify the responsible party to remedy the 

condition. The oven must be fully operational and tested before 

fi

 nalizing this document.

You may submit this form by either:

•   Gas Volume: Maximum input per cavity 85k BTU
  (25kW [Gross])        
•   Gas Pressure (Nat and LP): 6” W.C. (152.4 mmH

2

O) 

  (14.94 mb) min, 14” (350.6 mm H

2

O, 34.87 mb) max

Requirements:

•   Gas Shut-Off  Valve Size: A minimum .75 inch (19.05
  mm) I.D. full fl ow valve is required for single ovens.  
  A minimum 1 inch (25.4 mm) I.D. full fl ow valve is   
  required for double or triple ovens.
•   Ventilation: Operable at the time of this Start-Up

NOTE: 

It is the recipient’s responsibility to report to the freight company any concealed or non-concealed 

damage. Check the oven, attachments, installation kit, and oven shipping container for damage. The freight 

company must be noti

fi

 ed of any claims 

IMMEDIATELY

.

NOTE:

 It is the technician’s responsibility to understand and have available for reference the instructions listed 

in the Installation Manual, attached to this form. The manual contains crucial information regarding proper 

set-up and operation.

Initial Start-Up Checklist

START-UP

14

Power Specifi cations

Electrical

 

Gas

 

-Volume: Maximum input per cavity 

  85k BTU (25kW [Gross])

-Min. Pressure (Nat, LP, I

2H

, I

2E

, I

2E+

, I

2L

, and I

3P

):

  6” W.C. (152.4 mm H2O / 14.94 mb)

-Max. Pressure (Nat, LP, I

2H

, I

2E

, I

2E+

, I

2L

, and I

3P

):

  14” W.C. (350.6 mm H2O / 34.87 mb)

-Burner Pressure (Nat, LP, I

2H

, I

2E

, I

2E+

, and I

3P

):

  3.5” W.C. (88.9 mm H

2

O / 8.71 mb)

-Burner Pressure (I

2L

):

  4.0” W.C. (101.6 mm H

2

O / 9.96 mb)

North America

EU/Asia

Phase

1 Phase

1 Phase

Voltage

208/240 VAC

220-240 VAC

Frequency

50/60 Hz

50/60 Hz

Current Draw

8 Amp

8 Amp

Supply

3 Wire 

(L + L + G)

3 Wire 

(L + L + G)

Breakers

20 amp

16 amp

Plug

NEMA L620

IEC, 309 3 PIN

Содержание HHC-3240























Отзывы: