Turbo Ace matrix Скачать руководство пользователя страница 7

Страница: 7 / 74

Turbo Ace MATRIX

erected and properly tightened by turning the top locking cylinder in a clock-wise

direction. Next, loosen the arm screws located on top of the folding track. These

screws are keyed so they must be loosened and raised by about 1/8 of an inch in order

for the arms to fold, unfold the arms, and tighten them back in a clock-wise manner.

Make sure the round key located on the bottom of the screw is securely locked into

the circular key on the track. When it is properly locked in, it will prevent the arms

from accidentally folding during flight. Next, if you wish to fold the landing skid, you

may loosen the 2 side screws on each of the 4 legs. Pull the leg down to lengthen it.

Tighten the 2 screws back on each of the landing skid legs. Refer to section 5

TESTING & OPERATIONS (Please DO NOT install the propellers during the testing

procedure). Attach the battery to either on top or bottom of the Matrix. Lift the Matrix

up with one finger on each side from the center of Naza flight controller. Move the

battery until the Matrix is leveled like a see-saw with equal weight on both sides. See

Figure 3.4.4. It is important to note that the Matrix will not fly properly and may lose

control and crash if the center of gravity is not balanced at the middle of the Naza

flight control. Turn on the transmitter and within 2 seconds plug in the MATRIX

battery to bind. If your unit comes with DJI NAZA, please observe the blinking

yellow LED light located behind the quad, which indicates the controller is in warm

up stage. Wait for about 2 minutes until the yellow light stops flashing. Please check

the LED light description at section 5.3 and 5.4. Attitude mode is the most reliable

way to fly for intermediate to advance level pilots as all GPS is susceptible to

interference and sun spots activities. However, GPS remains to be the easiest and the

safest way to fly for beginners. Select the attitude mode from your transmitter, if you

are a trained pilot and use the GPS mode as a backup. Move both sticks of the

transmitter together in one action down to the lower right or left corner to start the

motors. Release right stick and immediately give the left stick about 10% throttles so

the motors will not cease. It will not lift off until the throttle stick passes 50%. Have

an experienced pilot test fly it on a bench while tied down. No defective claim is

allowed if the unit is crashed, so please be very careful.

1.4 Features



Extra wide 15-inch propellers for optimum flight time



High payload



High efficiency voltage with 6 cells Li-Po battery



Unobstructed front positioned camera mount



Center of gravity rolling camera compensation



Quick foldable design for easy portability

Содержание matrix











































































Результаты поиска

Содержание matrix

Отзывы:

Бренды по названию

Популярные бренды

Turbo Ace matrix, Руководство пользователя

Результаты поиска

Содержание matrix

Отзывы:

Бренды по названию

Популярные бренды