Turbo Ace matrix Скачать руководство пользователя

Страница: 32 / 74

Turbo Ace MATRIX

ELECTRONICS SETUP & ADJUSTMENT for

Spektrum DX 8 Transmitter

If you have purchased an RTF package

, please skip Section 4.1 through 4.5

because all settings are already complete and your MATRIX and transmitter have

been paired and test flown as a set. Unless you are familiar with the settings, any
changes might override the factory’s setting and disable the aircraft, affecting its

performance and flight reliability.

If you have purchased an ARF package

, you must complete Section 4.1 ESC

Programming and Section 4.2 Transmitter Calibration. MATRIX ESCs needs to

reprogram independently. Also, in order for a flight controller to work properly, your

specific transmitter has to be calibrated to work with each new MATRIX. Crashes

will be imminent if you skip these one-time procedures to match a MATRIX with a

transmitter.

4.1 ESC Programming for Spektrum DX 8 Transmitter (A Must

Setup For ARF)

Video Instruction:

How to calibrate the ESC for MATRIX:

https://www.dropbox.com/s/qwvt489g9j6zs7x/Calibration%20for%20Spektrum

%20ESCs.MP4

Please skip this ESC programming step if you have purchased RTF unit, since all

ESC have been re-programmed. Please follow the steps below very carefully, as they

will only take a few minutes.

Содержание matrix











































































Результаты поиска

Содержание matrix

Отзывы:

Похожие инструкции для matrix

Бренды по названию

Популярные бренды

Turbo Ace matrix, Руководство пользователя

Результаты поиска

Содержание matrix

Отзывы:

Похожие инструкции для matrix

Бренды по названию

Популярные бренды