manualshive.com logo in svg

TuffStuff TDH-345, Руководство пользователя

Поделиться
Скачать
TuffStuff TDH-345 Скачать руководство пользователя страница 17

6. Chrome plated surfaces should be cleaned regularly to

prolong the life and luster of the finish.  Wipe machine
down with a damp cloth and dry thoroughly each day or a
needed.

7. When checking the bolts and nuts, be sure they are a

fully fastened.  If there is a bolt or nut that continuousl
loosens obtain a replacement thru your local Tuff Stuff re
tailer or call our Customer Service Department.

8. Pay special attention to the Turn/ Pull Pins w/Knob (#72

located on the

Bar Holders (#4)

  and the

Bar Safeties

(#5)

.  Be sure they are fully engaged into the selectorized

holes of the 

Selectorized Uprights (#6)

.  Refer to 

Fig. 47

for further illustration.

9. Check that the 

Push Pull Pin 1/2” (#62)

  Hex Nut

 located

on the

Bottom Assembly Holder (#28)

 is fully fastened

(See

Fig. 48

) in addition, be sure the spring in the

Push

Pull Pin 1/2” (#62)

is operating freely.

10.Failure to perform routine maintenance could result i

personal injury and/or equipment damage.

M

aintenance Information

1. Lubrication of all moving parts is essential to the longevity 

and optimal performance of your Half Cage Ensemble.
Initial lubrication of some parts of your gym have been
done at the factory, but the

Chrome Post (#31)

  must be

lubricated regularly.  We recommend a clear aerosol, sili-
cone or teflon spray.

    Note

: Do not use oil based lubricants as they will attract

dust, dirt and grime, and will eventually gum up and erode 
bushings and sealed bearings.

2. All pulleys and bushings should be checked regularly for

signs of wear.

3. Check and adjust tension on cables periodically as it will

maintain proper anatomical function.

4. Periodically check all parts for signs of wear or damage. If 

there is a problem or replacement of a part is necessary,
STOP USING THE EQUIPMENT and immediately contact
your local Tuff Stuff retailer or call our Customer Service
Department.  Replace parts using only genuine Tuff Stuff 
parts.

5. Check welds to be free of cracks.

Maintenance

TDH 345 Half Cage Ensemble

16

Push Pull

Pin Hex Nut

Push Pull

Pin Hex Nut

Fig. 48 

Caution:

 Be sure the Push Pull Pin 

Hex Nut

 is fully

fastened. Fasten if necessary. 

Turn/ Pull Pin w/Knob Fully 
Engaged

Fig. 47

Caution:

Check that all Turn/ Pull Pins w/Knob (#72)

are fully engaged into the selectorized holes.

Содержание TDH-345





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды