TT electronics AB Connectors ABCIRP Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 41

background image

AB Connectors Limited

Specification No. 528

ABCIRP Connector Series

Assembly and wiring Instructions

AB Connectors Limited Issue 9: July 2010

Page 19 of 41

3. Screen Termination system.

3.1.1

Termination of shielded cables is necessary to provide R.F.I. or E.M.I. shielding
protection. The ABCIR Connector series has various methods for attaching shield
braid to the connector backshell.

3.1.2

This section details assembly methods using four different backshell styles. They will
be described as Method -A, B, C & D.

3.1.3

The following items are required to complete the assemblies.

3.1.4

Braid Sock: Provides the overall screen and is secured to the connector backshell
and the interwoven knitted mesh at the opposite end.

Typical Braided Sock

Connector Shell Size

Part Number

Length/Diameter

Up to shell size 32

ABBMBS035015

150mm / 35mm

Shell sizes 36 & 40

ABBMBS05015

150mm / 50mm

Braided Sock Lengths

Note.  Make  certain  the  sock  is  expanded  to  the  correct  diameter  before  cutting  to
length.  To  aide  this  operation,  the  use  of  an  inner  storage  tube  of  the  appropriate
diameter is recommended.

3.1.5

Knit Mesh: Interwoven between individual cable screens. Ensures all screens are
interconnected. Braid sock terminated to this component.

Knitmesh

3.1.6

Stainless Steel Locking Securing Band: Used to terminate outer overall screen to
backshell and interwoven knitted mesh.

Connector Shell Size

Part Number

Up to shell size 32

ABB600052

Shell sizes 36 & 40

ABB600090

Shell Size with Securing Band

«
...
17
18
19
20
21
...
»

Содержание AB Connectors ABCIRP Series










































Отзывы:

Нет отзывов

Похожие инструкции для AB Connectors ABCIRP Series

Бренд: AccuBoom Страницы: 12

Бренд: Intel Страницы: 50

Бренд: Clear-Com Страницы: 16

Бренд: Foss Страницы: 7

Бренд: Lux Tools Страницы: 84

Бренд: Performance Tool Страницы: 4

Бренд: Magnetek Страницы: 86

SolConeX 8581/41

Бренд: Stahl Страницы: 8

HDBT CHDBT-1H7CL

Бренд: CYP Страницы: 16

Бренд: AV Access Страницы: 16

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 3

Бренд: Oasis Страницы: 12

Бренд: TE Connectivity Страницы: 6

AMPACT 83452 Series

Бренд: TE Connectivity Страницы: 4

Бренд: Icom Страницы: 2

Бренд: Audio Technica Страницы: 2

Бренд: MOB Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды