TT electronics AB Connectors ABCIRP Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 41

background image

AB Connectors Limited

Specification No. 528

ABCIRP Connector Series

Assembly and wiring Instructions

AB Connectors Limited Issue 9: July 2010

Page 24 of 41

8.6

Method C: Electrical Termination

8.6.1

Method C uses two stainless steel clamp bands that concentrically close to
mechanically grip and electrically terminate the overall shield to:

•

The wire bundles or multi-core cables.

•

Connector backshell and ‘CRA’ accessory, providing an interface to a conduit
system.

8.6.2

The following outlines the procedure for the Fixed Connector With SCHSA & CRA
Accessory.

8.6.3

Strip cable outer insulation exposing the screen for a length of 170mm.

8.6.4

Cut back the screen leaving a length of 100/125mm.

8.6.5

Crimp the contacts on, load the connector and assemble the grommet as per the
instructions on pages 7 to 11 inclusive.

Braid Sock Assembly

8.6.6. Cut the braid sock to the required length and remove inner storage tube. Slide the

braid sock over knurled section of the inner component of CRA accessory and
terminate using a securing band shown in Appendix C. Ideally apply the band close to
the end of the knurled section checking for a neat termination with no twisting of the
band. Do not fold back braid screen when terminating braid to the CRA shell. When
terminating, trim edges to produce a clean cut so as not to damage the ‘O’ring seal.

8.6.7. Slide the chosen conduit assembly down the cable and away from the work area.

«
...
22
23
24
25
26
...
»

Содержание AB Connectors ABCIRP Series










































Отзывы:

Нет отзывов

Похожие инструкции для AB Connectors ABCIRP Series

Бренд: Linksys Страницы: 2

Бренд: i.safe MOBILE Страницы: 208

Бренд: JAE Страницы: 13

Бренд: Sealey Страницы: 2

Бренд: Sealey Страницы: 14

Shielded KeyConnect Patch Panel

Бренд: Belden Страницы: 2

Бренд: Agilent Technologies Страницы: 7

Бренд: NEUTRIK Страницы: 13

Бренд: Terra Страницы: 17

Бренд: Pentair Страницы: 20

Бренд: ENFORCER Страницы: 2

Бренд: ENFORCER Страницы: 2

Бренд: ENFORCER Страницы: 4

Бренд: DVDO Страницы: 12

Бренд: EXEL ACOUSTICS Страницы: 20

Бренд: Hakko Electronics Страницы: 12

Бренд: Hall Research Technologies Страницы: 12

Dormont ReliaGuard

Бренд: Watts Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды