TT electronics AB Connectors ABCIRP Series Скачать руководство пользователя страница 40

Страница: 40 / 41

AB Connectors Limited

Specification No. 528

ABCIRP Connector Series

Assembly and wiring Instructions

AB Connectors Limited Issue 9: July 2010

Page 40 of 41

Connectors will not mate

Attempting to couple
connectors with different
insulator orientations

Contacts bent or damaged.

Socket contact clips damaged.

Ensure the connectors are the same
orientation. Check coloured
identification band.

Check contacts for signs of damage

Check socket contact clips for signs of
damage.

High resistance, intermittent or no contact

Socket contact clips missing.

Poor crimp joints.

Wire broken or damaged.

Check contact for missing clip.

Check crimp and crimp tool settings

Check wire for signs of damage
including very tight bend radii.

Problem locking the backshell to the plug
connector

Connector difficult to grip due to
rotating coupling nut.

Mate the plug connector to a suitable fixture
prior to tightening.

Содержание AB Connectors ABCIRP Series










































Результаты поиска

Содержание AB Connectors ABCIRP Series

Отзывы:

Похожие инструкции для AB Connectors ABCIRP Series

Бренды по названию

Популярные бренды

TT electronics AB Connectors ABCIRP Series, Инструкции по сборке и подключению

Результаты поиска

Содержание AB Connectors ABCIRP Series

Отзывы:

Похожие инструкции для AB Connectors ABCIRP Series

Бренды по названию

Популярные бренды