TSI Instruments 3786 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 83

background image

B-16

Model 3786 Ultrafine Water-based Condensation Particle Counter

D a t a R e p o r t i n g R e c o r d s

D Record (data)

D,Mode,Flags,CN,ST,LT,CNT,PM,RP

D Record

Identifier

Mode Current Operating mode
Flags Status Flags

Weighting

Description

1

Live-time was less than minimum set by SLM command for at least a
portion of the sample

2

Overflow of data in one of the data record fields

4

The flow was out of range for some portion of the sample

8

Absolute pressure out of range for some portion of the sample

10

Reserved

20

A drain cycle was in process during the sample or the reservoir was
detected full

40

Set if dry wick was detected during the sample

80

Set if reservoir full for ten minutes and water injection has stopped

100

Saturator, Growth Tube, or Optics temperatures were out of range
during the sample.

200

The laser power was out of range for some portion of the sample.

400

UWCPC in warm-up period

1000

Set during front porch period of a scanning sample

2000

Set during the back porch period of a scanning sample

CN

Aggregated Concentration—This concentration value is calculated by dividing
the accumulated aggregate counts by the live-time of the sample * 5.0. The
aggregated counts and live-times are accumulated each tenth-second interval.
If the live-time value for the interval is less than 10%, the aggregated counts
are calculated based on the overflow concentration of 9.99e5. Otherwise the
aggregated counts accumulated are the total counts detected during the
interval and live-time is the live-time value for the interval.

The overflow flag will be set when the concentration value exceeds 9.99e5.

ST

Sample time (elapse time) 0.1 second resolution (0.1 to 3600).

LT

Live time 0.1 second resolution (0.1 - 3600).

CNT

Accumulated particle counts.

PM

Place holder, always 0.

RP

Raw Photometric value.

«
...
72
73
74
75
76
...
»

Содержание 3786




















































































Отзывы:

Нет отзывов

Похожие инструкции для 3786

Бренд: Samsung Страницы: 183

Бренд: Casio Страницы: 8

Бренд: Hengstler Страницы: 167

BEETLE /Express

Бренд: Wincor Nixdorf Страницы: 34

Veeder-Root C346 Series

Бренд: Danaher Страницы: 20

Бренд: JCM Страницы: 11

Бренд: JCM GLOBAL Страницы: 124

Бренд: Sam4s Страницы: 9

Бренд: Olivetti Страницы: 24

TEC MA-1040-100 Series

Бренд: TEC Страницы: 48

Бренд: Royal Страницы: 140

Rp5000 - Point of Sale System

Бренд: HP Страницы: 78

Бренд: VAKI Страницы: 42

Бренд: TEC Страницы: 72

TeamPoS 3000 XE

Бренд: Fujitsu Страницы: 8

Бренд: red lion Страницы: 4

Бренд: Yoosol Electronics Страницы: 14

Бренд: Scan Coin Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды