TSI Instruments 3786 Скачать руководство пользователя | Manualshive

Страница: 41 / 83

background image

C H A P T E R 4

D a t a C o l l e c t i o n

4-1

This chapter contains information related to the UWCPC’s data
interfaces and optional embedded PC/104 single board computer
for data collection.

D a t a I n t e r f a c e s

The UWCPC provides several data interfaces allowing for flexible
data collection and instrument control. There are four connectors
on the back panel. Two connectors provide direct access to the
UWCPC and the remaining two provide access to the optional
PC/104 single board computer (SBC). The connectors are:

Serial

Standard RS-232 type serial communications.
This interface is provided through the 9-pin D-
Sub connector on the back panel of the UWCPC.
The connector pin-out is given in Table 4-1.

USB

Universal Serial Bus communications. This
interface provides an alternate path for the serial
interface mentioned above. To a host computer,
this interface acts like an additional serial port to
the computer.

PC/104 Serial

Serial communications to the optional internal
PC/104 SBC (PC/104 Com1)

PC/104 Ethernet Ethernet connection to the optional internal

PC/104 SBC (PC/104 eth0)

Table 4-1.

Serial Connector Signal Connections

Pin Number

Signal

Direction

2

RXD

INPUT TO UWCPC

3

TXD

OUTPUT FROM UWCPC

5 GND

—

When the PC/104 SBC is installed there is an internal connection
between the UWCPC and the PC/104 SBC. If the UWCPC is
purchased without the optional PC/104 SBC, the associated
connectors have no internal connections to the UWCPC.

«
...
39
40
41
42
43
...
»

Содержание 3786




















































































Отзывы:

Нет отзывов

Похожие инструкции для 3786

Бренд: National Cash Register Страницы: 22

Бренд: TEC Страницы: 164

PASPort PS-2117

Бренд: PASCO Страницы: 4

ASCOLINE 700 AEH 2 Series

Бренд: ascobloc Страницы: 15

Бренд: Honeywell Страницы: 10

Бренд: Toshiba Страницы: 150

H7CX-Ax-N Series

Бренд: Omron Страницы: 2

Бренд: Simpson Страницы: 35

Бренд: Royal Страницы: 57

Бренд: Grace Страницы: 10

Бренд: Lamassu Страницы: 4

Бренд: Star Micronics Страницы: 17

Бренд: JAMAR Technologies Страницы: 32

Бренд: Olivetti Страницы: 45

Бренд: Sanela Страницы: 4

Бренд: NRI Страницы: 51

Бренд: TEC Страницы: 52

Бренд: Olivetti Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды