TSI Instruments 3786 Скачать руководство пользователя страница 12

Страница: 12 / 83

Model 3786 Ultrafine Water-based Condensation Particle Counter

Water System........................................................................ 3-6

Drain Modes ......................................................................... 3-7

Sample Inlet Connection ....................................................... 3-8

4 Data Collection

.................................................................... 4-1

Data Interfaces...................................................................... 4-1

USB Driver Software ............................................................. 4-3

Communications Parameters ................................................ 4-4

Terminal Communications .................................................... 4-4

PC/104 Single Board Computer Option ................................ 4-5

5 Maintenance and Troubleshooting

..................................... 5-1

Replacing Wick ..................................................................... 5-1

Flow Calibration.................................................................... 5-1

Troubleshooting .................................................................... 5-3

Water in the Sample Inlet...................................................... 5-4

Little or No Water Flows During Drain Cycle ......................... 5-4

Water Spurts Out of Pump Exhaust ...................................... 5-5

High or Low Photometric Readings ........................................ 5-6

Rapidly Flashing Status Indicator—Laser.............................. 5-7

Technical Contacts................................................................ 5-7

Returning the UWCPC for Service.......................................... 5-8

A p p e n d i x e s

A Specifications

......................................................................A-1

B Firmware Commands

........................................................... B-1

Commands—Quick Reference .............................................. B-1

Read Commands .................................................................. B-2

Set Commands..................................................................... B-4

Data Reporting Records ..................................................... B-16

I n d e x

Index ........................................................................................ I-1

Содержание 3786



















































































Результаты поиска

Содержание 3786

Отзывы:

Похожие инструкции для 3786

Бренды по названию

Популярные бренды

TSI Instruments 3786, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 3786

Отзывы:

Похожие инструкции для 3786

Бренды по названию

Популярные бренды