TSC TTP-384M Скачать руководство пользователя

Страница: 51 / 59

Not Printing

* Cable is not well connected to serial or

USB interface or parallel port.

* The serial port cable pin configuration

is not pin to pin connected.

* Re-connect cable to interface.
* If using serial cable,

- Please replace the cable with pin to pin

connected.

- Check the baud rate setting. The default baud

rate setting of printer is 9600,n,8,1.

* If using the Ethernet cable,

- Check if the Ethernet RJ-45 connector green

LED is lit on..

- Check if the Ethernet RJ-45 connector amber

LED is blinking.

- Check if the printer gets the IP address when

using DHCP mode.

- Check if the IP address is correct when using

the static IP address.

- Wait a few seconds let the printer get the

communication with the server then check the
IP address setting again.

* Chang a new cable.
* Ribbon and media are not compatible.
* Verify the ribbon-inked side.
* Reload the ribbon again.
* Clean the printhead.
* The print density setting is incorrect.
* Printhead’s harness connector is not well

connected with printheat. Turn off the printer
and plug the connector again.

* Check if the stepping motor is plugging in the

right connector.

* Check your program if there is a command

PRINT at the end of the file and there must have
CRLF at the end of each command line.

Memory full

( FLASH / DRAM )

* The space of FLASH/DRAM is full.

* Delete unused files in the FLASH/DRAM.
* The max. numbers of file of DRAM is 256 files.
* The max. user addressable memory space of

DRAM is 2048 KB.

* The max. numbers of file of FLASH is 256 files.
* The max. user addressable memory space of

FLASH is 6656KB.

SD card is unable to

use

* SD card is damaged.
* SD card doesn’t insert correctly.
* Use the non-approved SD card

manufacturer.

* Use the supported capacity SD card.
* Insert the SD card again.
* The supported SD card spec.

- 128MB
- 256MB
- 512MB
- 1GB
- 4GB SDHC CLASS 6

* Approved SD card manufacturers; SanDisk,

Transcend

PS/2 port does not

work

* Did not turn off power prior to plug in

the PS/2 keyboard.

* PS/2 keyboard is damaged.
* PS/2 keyboard doesn’t plug-in

correctly.

* There is no BAS file in the printer.

* Turn off printer power prior to plug in the PS/2

keyboard .

* Plug the PS/2 keyboard again.
* Make sure the keyboard is fine.
* Make sure if there is any BAS file downloaded

into printer.

Содержание TTP-384M




























































Результаты поиска

Содержание TTP-384M

Отзывы:

Похожие инструкции для TTP-384M

Бренды по названию

Популярные бренды

TSC TTP-384M, Руководство пользователя

Результаты поиска

Содержание TTP-384M

Отзывы:

Похожие инструкции для TTP-384M

Бренды по названию

Популярные бренды