TSC TTP-2410MT Series Скачать руководство пользователя страница 55

Страница: 55 / 87

- 48 -

5.8

Diagnostics

5.8.1

Print Config.

This feature is used to print current printer configuration to the label. On the configuration

printout, there is a print head test pattern, which is useful for checking if there is any dot

damage on the print head heater element.

Self-test printout

Model name
F/W version
Firmware checksum
Printer S/N
TSC configuration file
System date
System time
Printed mileage (meter)
Cutting counter

Print speed (inch/sec)
Print darkness
Label size (inch)
Gap distance (inch)
Gap/black mark sensor
intension
Code page
Country code

Menu

Diagnostics

Print Config.

Dump Mode

Print Head

Display

Sensor

Menu

Diagnostics

Print Config.

Содержание TTP-2410MT Series
























































































Результаты поиска

Содержание TTP-2410MT Series

Отзывы:

Похожие инструкции для TTP-2410MT Series

Бренды по названию

Популярные бренды

TSC TTP-2410MT Series, Руководство пользователя

Результаты поиска

Содержание TTP-2410MT Series

Отзывы:

Похожие инструкции для TTP-2410MT Series

Бренды по названию

Популярные бренды