TSC TTP-2410MT Series Скачать руководство пользователя страница 46

Страница: 46 / 87

- 39 -

5.3

TSPL2

This

“TSPL2” category can set up the printer settings for TSPL2.

Item

Description

Default

Speed

Use this item to setup print speed. The each increase or decrease
is 1 ips. Available setting is from 4 to 12.

Density

Use this option to setup printing darkness. The available setting is
from 0 to 15, and the step is 1. You may need to adjust your
density based on selected media.

Direction

The direction setting value is either 1 or 0. Use this item to setup
the printout direction.

DIRECTION 0

DIRECTION 1

Print mode

This item is used to set the print mode. There are 5 modes as
below,

Printer Mode

Description

None

Next label top of form is aligned to the print head burn
line location. (Tear Off Mode)

Batch Mode

Once image is printed completely, label gap/black
mark will be fed to the tear plate location for tear
away.

Batch

Mode

Menu

TSPL

Speed

Density

Direction

Print mode

None

Batch Mode

Peeler Mode

Cutter Mode

Cutter Batch

Offset

Shift X

Shift Y

Reference X

Reference Y

Code Page

Country

FE
E

Содержание TTP-2410MT Series
























































































Результаты поиска

Содержание TTP-2410MT Series

Отзывы:

Похожие инструкции для TTP-2410MT Series

Бренды по названию

Популярные бренды

TSC TTP-2410MT Series, Руководство пользователя

Результаты поиска

Содержание TTP-2410MT Series

Отзывы:

Похожие инструкции для TTP-2410MT Series

Бренды по названию

Популярные бренды