7
has to use SDS-plus tools that are to be inserted into the SDS-plus holder
(
1
) of the machine.
To drill boreholes in steel or wood the tools without the SDS-plus
functionality are used (e.g. drilling bits with cylindrical shanks). For such
tools quick locking drilling chucks or chucks with a toothed ring are
necessary.
CAUTION:
Do never use tools without the SDS-plus functionality for impact
drilling or chiseling! The non-SDS-plus tools and corresponding drilling
chucks shall definitely get damaged during impact drilling or chiseling.
Installation of the drilling chuck with a toothed ring
(Fig.
C
)
Screw the SDS-plus adapter stud (
1
5
) into the drilling chunk with a
toothed ring (
1
4
).
Lock the drilling chunk with a toothed ring (
1
4
) with use of the
securing bolt (
1
3
).
NOTE:
Please remember that the securing bolt has the left-hand thread.
Slide the adapter stud into the SDS-plus tool holder (
1
) with
simultaneous rotation of the drilling chuck until the adapter is
automatically locked.
Check reliability of locking by pulling the drilling chuck with a toothed
ring outwards.
Removing of the drilling chuck with a toothed ring
(Fig.
Turning on/off
ź
To turn the power tool on press its switch (
9
) button and keep it
pressed
.
ź
To turn the power tool off just release the switch (
9
) button
.
ź
Clean the working tool carefully after removing it from the chuck
.
n
ź
Install the drilling chuck with a toothed ring (
1
4
).
ź
Open the drilling chuck with a toothed ring by rotating the sleeve so
much as to enable sliding the working tool shank into the chuck.
Insert the working tool.
ź
Insert the key (
1
6
) into appropriate holes of the drilling chuck with a
toothed ring and uniformly fix the working tool.
ź
Reposition the switch (
7
) into the symbol 'No-impact drilling'
- .
n
Removing working tools without SDS-plus functionalities
CAUTION:
Right after completion of working the tool may be really hot.
Avoid direct contact with a tool and wear appropriate protecting gloves.
n
ź
Use the key (
1
6
) designed for the drilling chuck to rotate the sleeve of
ź
the drilling chuck with a toothed ring (
1
4
) clockwise until the
working tool is released.
ź
ź
Clean the working tool carefully after removing it from the chuck
.
n
Selection of the operation mode
NOTE:
The operation mode of the machine can be switched over only when
ź
Clean the rear end of the tool to be installed and
l
ithium
grease it
the machine is off! Otherwise the electric device may be damaged.
slightly.
Operation mode of the machine can be selected with use of the
ź
operation mode selector switch (
7
).
To change the operation mode it is necessary to depress the button (
6
)
that releases locking of the operation mode selector switch and
ź
reposition the switch to the desired position until engagement of the
locking pawl is heard.
n
No-impact drilling (
Fig.
1
):
ź
Pull the locking sleeve (
3
) backwards and slide the drilling chuck with
Set the switch (
7
) to the symbol
-
.
a toothed ring (
1
4
) out of the tool holder.
ź
After removing the replaceable drilling chuck with a toothed ring (
1
4
)
Impact drilling
(Fig.
2
):
must be protected from dirt. When necessary, slightly grease the
Set the switch (
7
) to the symbol
- .
toothed dog.
Chiseling (rotation disabled)
(Fig.
3
):
n
Set the switch (
7
) to the symbol -
.
The SDS-plus tool holder makes it possible to replace a working tool
When the switch is set to the position
easily and conveniently with no need to use additional tools.
'Chiseling', the impac t rate is
Due to the system feature, working tools of the SDS-plus type move in
automatically increased, which enables
the holder with a little play. It is why axial run-out occurs when the
the tool to perform chiseling with the
machine runs with the idle speed. It has no influence onto dimension
higher performance.
accuracy of the borehole to be drilled as the drilling bit is self-centered
during drilling.
Repositioning of the chisel
(Fig.
4
):
The dust protection hood (
2
) substantially prevents from penetration of
Insert a chisel into the tool holder
.
dust into the tool holder during the machine operation. Take care to avoid
Rotate the operation mode switch (
7
) to
damaging the dust hood (
2
) while inserting a tool into the tool holder.
the position -
.
Damaged dust protection hood must be immediately replaced. It is
Rotate the tool holder to set the chisel to
recommended to have the dust hood replaced at a service workshop.
the desired working position.
n
Installation of the SDS-plus working tool
(Fig.
F
)
Set the operation mode selector switch
(
7
) to the position 'Chiseling'. Thus, the
ź
Clean the rear end of the tool to be installed and grease it slightly.
tool holder is locked in its position.
ź
Insert the tool into the tool holder with simultaneous rotation until
the tool shank is automatically locked inside the holder.
While chiseling the operation mode selector switch (
7
) must always
remain in the position 'Chiseling'.
ź
Check reliability of locking by pulling the tool outwards.
n
Removing SDS-plus
working tool
(Fig.
G
)
n
CAUTION:
Right after completion of working the tool may be really hot.
Avoid direct contact with a tool and wear appropriate protecting gloves.
ź
Push back the locking sleeve (
3
) and remove the tool.
D
)
Tool replacement
SDS-plus
Installation
of working tools without SDS-plus functionalities
(Fig
.
E
)
2
3
4
1
Содержание TMM710K
