Tryton TMM710K Скачать руководство пользователя страница 6

Страница: 6 / 44

Drilling depth limiter – 1 pc.

Flat chisel – 1 pc.

Point chisel – 1 pc.

SDS-plus drilling tools – 3 pcs

(8,10,12 mm)

Rubber ring for dust collection – 1 pc.

Carbon brushes

–

2 pcs.

Transportation case – 1 pc.

–
–

Fig. A

SDS-plus tool holder

Dust protection hood

Locking sleeve

Drilling depth limiter

Fixing button to fit the drilling depth limiter

Button to release locking of the operation mode selector

BEFORE YOU START:

switch

Make sure that the power source parameters match the tool

Operation mode selector switch

parameters on the data plate.

Main handle with a slip resistant pad

Make sure that the on/off switch (

) of the tool is in the off position.

On/Off trigger

Always work with use of the auxiliary handle (

). Risk of accidents

10.

Power cord

at work can be avoided or mitigated if the machine is reliably held in
both hands. The auxiliary handle is to be attached by encompassing

11.

Brush-holder

the tool holder with the handle clamp and then the clamp is locked

12.

Auxiliary handle

by rotating the handle clockwise.

Fig. C

13.

Securing bolt for the drilling chuck with a toothed ring

The auxiliary handle can be swiveled to whichever direction to

14.

Drilling chuck with a toothed ring

enable the operator to work in a convenient position of the body and

15.

Adapter stud to fix the drilling chuck to the SDS-plus socket

to avoid excessive fatigue. After rotating the handle anticlockwise

Fig. E

16.

Key for the drilling chuck with a toothed ring

swivel it to the desired position and the retighten the clamp by

Fig. F

17.

Rubber ring for dust collection

rotating the handle clockwise for final fixation

Not all accessories presented or described herein are provided as standard

with the power tool.

SPECIFICATIONS:

While using an extension cord make sure that its parameters and

wire cross-sections match the tool parameters. Extension cords
should be as short as possible. When in use extension cords must be
fully uncoiled.

ADJUSTMENT DURING WORKING WITH THE TOOL:

Adjustment of the drilling depth

(Fig.

)

The drilling depth limiter (

) is designed to set the desired depth of the

drilling bit immersion

into the material. For that purpose do the

following:

insert the shank of the SDS-plus working tool into the holder (

) and

drive it home. Otherwise, excessive play of the SDS-plus tool may lead
to incorrect setting of the drilling depth;
depress the fixing button(

) for the drilling depth limiter and slide the

limiter so much as to make the distance between the tip of the drilling
bit and the tip of the limiter correspond to the desired drilling depth

lock the depth limiter by releasing the fixing button.

Selection of drilling tools (bits)

For impact drilling in concrete, bricks or stone as well as for chiseling one

User's manual 1 p

Warranty card 1 p

Device components

The numbers of tool components refer to the image presented on pages 2-3
of the user manual:

The vibration level value given refers to basic application of the tool. If the

tool  is  used  for  other  applications  or  with  other  tools,  or  if  it  is  not
maintained  properly,  the  vibration  level  may  differ  from  the  values
given. The  above-mentioned  causes  may  lead  to  higher  exposure  to
vibrations during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.

2.
3.

(Fig.

By pressing the fastener button (

) slide the drill depth stop (

) into

the auxiliary handle hole and lock it by releasing the fastener
button. The numbers on the drill depth stop should be visible from
the top.

Vibration level according to valid standard

hammer drilling in

concrete

h HD

- t

olerance of measurements