6
ź
Lock the drilling chunk with a toothed ring (
1
2
) with use of the
securing bolt (
1
1
).
NOTE:
Please remember that the securing bolt has the left-hand thread.
ź
Clean the rear end of the stud to be inserted into the tool holder and
grease it slightly.
ź
Slide the adapter stud into the SDS-plus tool holder (
1
) with
simultaneous rotation of the drilling chuck until the adapter is
automatically locked.
ź
Check reliability of locking by pulling the drilling chuck with a toothed
ring outwards.
Removing of the drilling chuck with a toothed ring
(Fig.
Turning on/off
To turn the power tool on press its switch (
8
) button and keep it pressed.
To turn the power tool off just release the switch (
8
) button
.
TIPS REGARDING OPERATION:
ź
To drill holes in ceramic tiles set the operation mode switch (
6
) to
position
. Once the hole in the ceramic tile is ready,
set the operation mode switch to position «impact drill» and continue
ź
Open the drilling chuck with a toothed ring (
1
2
) by rotating the sleeve
(
1
5
) so much as to enable sliding the working tool shank into the
chuck. Insert the working tool.
ź
Insert the key (
1
4
) into appropriate holes of the drilling chuck with a
toothed ring (
1
2
) and uniformly fix the working tool.
ź
Reposition the switch (
6
) into the symbol 'No-impact drilling'
- .
n
Removing working tools without SDS-plus functionalities
CAUTION:
Right after completion of working the tool may be really hot.
Avoid direct contact with a tool and wear appropriate protecting gloves.
ź
Use the key (
1
4
) designed for the drilling chuck to rotate the sleeve of
n
the drilling chuck with a toothed ring (
15
) clockwise until the
ź
Pull the locking sleeve (
3
) backwards and slide the drilling chuck with
working tool is released.
a toothed ring (
1
2
) out of the tool holder.
ź
Clean the working tool carefully after removing it from the chuck
.
ź
After removing the replaceable drilling chuck with a toothed ring (
1
2
)
n
Selection of the operation mode
must be protected from dirt. When necessary, slightly grease the
NOTE:
The operation mode of the machine can be switched over only when
toothed dog.
the machine is off! Otherwise the electric device may be damaged.
n
Operation mode of the machine can be selected with use of the
The SDS-plus tool holder makes it possible to replace a working tool
operation mode selector switch (
6
).
easily and conveniently with no need to use additional tools.
To change the operation mode it is necessary to depress the button (
5
)
Due to the system feature, working tools of the SDS-plus type move in
that releases locking of the operation mode selector switch and
the holder with a little play. It is why axial run-out occurs when the
reposition the switch to the desired position until engagement of the
machine runs with the idle speed. It has no influence onto dimension
locking pawl is heard.
accuracy of the borehole to be drilled as the drilling bit is self-centered
No-impact drilling (
Fig.
1
):
during drilling.
Set the switch (
6
) to the symbol -
The dust protection hood (
2
) substantially prevents from penetration of
dust into the tool holder during the machine operation. Take care to avoid
Impact drilling
(Fig.
2
):
damaging the dust hood (
2
) while inserting a tool into the tool holder.
Set the switch (
6
) to the symbol -
Damaged dust protection hood must be immediately replaced. It is
Chiseling (rotation disabled)
(Fig.
3
):
recommended to have the dust hood replaced at a service workshop.
Set the switch (
6
) to the symbol -
n
Installation of the SDS-plus working tool
When the switch is set to the position
ź
Clean the rear end of the tool to be installed and grease it slightly.
'Chiseling', the impac t rate is
ź
Insert the tool into the tool holder with simultaneous rotation until
automatically increased, which enables
the tool shank is automatically locked inside the holder.
the tool to perform chiseling with the
ź
Check reliability of locking by pulling the tool outwards.
higher performance.
Repositioning of the chisel
(Fig.
4
):
Insert a chisel into the tool holder
.
Rotate the operation mode switch (
6
) to
the position -
Rotate the tool holder to set the chisel to
n
Removing SDS-plus
working tool
the desired working position.
CAUTION:
Right after completion of working the tool may be really hot.
Set the operation mode selector switch
Avoid direct contact with a tool and wear appropriate protecting gloves.
(
6
) to the position 'Chiseling'. Thus, the
ź
Push back the locking sleeve (
3
) and remove the tool.
tool holder is locked in its position.
While chiseling the operation mode selector switch (
6
) must always
ź
Clean the working tool carefully after removing it from the chuck
.
remain in the position 'Chiseling'.
n
n
'No-impact drilling'
ź
Install the drilling chuck with a toothed ring (
1
2
).
D
)
Tool replacement
Installation
of working tools without SDS-plus functionalities
(Fig
.
E
)
2
3
4
1
Содержание TMM10034
