Trycom Technology TRP-C68 Скачать руководство пользователя страница 25

Страница: 25 / 34

7-5. Read the module’s Firmware

Command

ID 46 07 00 (CRC)

Syntax
Description

Address of setting module 1~247

Function Code

Read module’s Firmware

Reserved code

Response

ID 46 07

00(CRC)

ID 46 20 ……Module command Line

:Year,

:Month ,

DD:

Date ,

00 : Reserved code

ID C6 00 (CRC)

ID C6 (CRC) C6:Error function code 00 : Reserved code

Example:

Send Command:

”

01 46 07 00

”……

.Set up TRP-C68’s configuration,

Response:”

01 46 07 07 04 07 00“…2007 /04/07 12.2006 TRP-C68 Firmware Version,

Error Response: “01 C6 00 ”……Error code.

7-6.Read the reset status

Command

ID 46 08 00 (CRC)

Syntax
Description

Address of setting module 01~247

Function code

Read reset status

Reserved code

Response

ID 46 08 XX 00 (CRC)

ID 46 08 00 ….Module command Line

XX=01 Have been reset , 00:Have been read

ID C6 00 (CRC)

ID C6 (CRC) C6:Error function code 00 : Reserved code

Example:

Send Command:

”

01 46 08 00

”……

.Read the TRP-C68’s reset status,

Response:

”

01 46 08 01 00 “……Have been reset,

Error Response: “01 C6 00 ”……Error code.

Содержание TRP-C68



































Результаты поиска

Содержание TRP-C68

Отзывы:

Trycom Technology TRP-C68, Руководство пользователя, Страница: 25 / 34

Результаты поиска

Содержание TRP-C68

Отзывы: