background image

TractionAir

21

PRESSURE SENSOR FAIL

 

Should either pressure transducer get 5psi out of specification with it’s partner, 
the ECU will enter the pressure transducer failure mode. At this point the exhaust 
valves are turned off and the vehicle tyre pressure will return to vehicle pressure. 
The affected pressure transducer will need to be replaced. This can be done 
relatively simply however, prior to starting this you will need to identify the affected 
transducer and override it to allow the vehicle to carry on working until the faulty 
transducer can be replaced. This can done through placing an inline gauge on the 
external hose at the tyres, the pressure transducer that reads the same pressure 
as the gauge is the one that is reading correctly The main screen display is PT1 
and the small read-out is PT2. These transducers are both clearly labeled in the 
pressure cell.

Pressure Sensor Failure & Manual Overide Selection Instructions 

(EC9 only)

Press ‘

MAX TRACTION’ 

 and then 

‘POWER’

  (press and release) to turn the 

controller 

ON

 and enter the 

PRESSURE

 Sensor Selection mode. 

The 

‘MAX TRACTION’

 button must be pressed for 4 seconds before the 

PRESSURE

 Sensor Selection mode is enabled and the following displayed.

 

Use the 

GPS ‘ON’

  button to move the 

pointer (◄ ) to select the required option.

PT1 selects Pressure Sensor 1 as the main 
and only pressure sensor.
PT2 selects Pressure Sensor 2 as the main 
and only pressure sensor.
PT1 or PT2 can only be selected if a sensor 
has failed in the below PT1+PT2 mode.

‘Use GPS ON Key
To Select
Saves After 5 sec
 

  

PT1: 

PT2 
PT1+PT2:’   

  

PT1+PT2 selects PT1 as the main pressure sensor with PT2 being used to check 
PT1 for accuracy. 

After five seconds the selection is saved and the controller starts normal operation. 
If 

‘Memory Errors’

 is displayed repeat the selection as described above in a).

In the PT1+PT2 mode if either PT1 or PT2 differ by more than 5 PSI then an alarm 
will be triggered and the fill output will stay on continuously.  
Reselecting the PT1+PT2 mode will cancel the alarm flag and the message 

Содержание TractionAir





























Отзывы: