Trotec PRDS 10-230V Скачать руководство пользователя

Страница: 12 / 17

Operating manual – rotary hammer PRDS 10-230V

Selecting the operating mode

With the function selector switch (3) you can choose drilling /
hammer drilling or chiselling. Via the switch for the impact
mechanism (12) you either activate (hammer drilling or
chiselling) or deactivate (drilling) the impact mechanism.

Note
Only operate the function selector switch (3)
during operation!

Otherwise the device might be

damaged.

Note
Only operate the switch for the impact
mechanism (12) when the device is at a standstill!

Otherwise the device might be damaged.

1. Set the function selector switch (3) to the desired position.

The function selector switch comes with a safety lock that
has to be pushed in first, before you can change the switch
position.

2. Set the switch for the impact mechanism (12) to the

desired position.

Operating mode: Drilling

Operating mode: Hammer drilling

Содержание PRDS 10-230V


















Результаты поиска

Содержание PRDS 10-230V

Отзывы:

Похожие инструкции для PRDS 10-230V

Бренды по названию

Популярные бренды

Trotec PRDS 10-230V, Оригинальное руководство пользователя

Результаты поиска

Содержание PRDS 10-230V

Отзывы:

Похожие инструкции для PRDS 10-230V

Бренды по названию

Популярные бренды