WWW.AWC608.COM
2) In the normal standby interface of the panel, click "Settings" in
the lower left corner to enter the high and low setting interface
3) Low point setting: After selecting "Tool head
movement" to move down the UD1 axis. When the tool tip is close
to the adsorption table, switch the UD1 axis to slow movement,
when the tool tip is attached the surface of the table, stop movin
and click "Set Current Position to Low Point". If you are familiar with
the low point of your machine, you can directly modify the low point
data.
4) High point setting: put a small piece of material(which can be
chose a little thicker) to be processed
select "tool head-1", click "axis movement", move the UD1 axis
upward, move the tip of the knife to the top of the material surface,
stop moving, and click "Set Current Position to High Point". If you
are familiar with the h
modify the high point data. The distance of the high point must be
greater than the thickness of the material! , It is not advisable to set
the maximum value, this will reduce the cutting efficiency, just set
moderate.
5) Similarly, the settings of other cutter heads are as in steps 1
7. Distance Per Pulse value commissioning of R axis.
1): Set the starting point at the current point after the machine is
reset, and make a mark on the cutter head and the cutter
shown in the figure
Motion controller user manual
2) In the normal standby interface of the panel, click "Settings" in
the lower left corner to enter the high and low setting interface
Low point setting: After selecting "Tool head-1", click "Axis
movement" to move down the UD1 axis. When the tool tip is close
to the adsorption table, switch the UD1 axis to slow movement,
when the tool tip is attached the surface of the table, stop movin
and click "Set Current Position to Low Point". If you are familiar with
the low point of your machine, you can directly modify the low point
4) High point setting: put a small piece of material(which can be
chose a little thicker) to be processed on the surface of the platform,
1", click "axis movement", move the UD1 axis
upward, move the tip of the knife to the top of the material surface,
stop moving, and click "Set Current Position to High Point". If you
are familiar with the high point of your machine, you can directly
modify the high point data. The distance of the high point must be
greater than the thickness of the material! , It is not advisable to set
the maximum value, this will reduce the cutting efficiency, just set
5) Similarly, the settings of other cutter heads are as in steps 1
7. Distance Per Pulse value commissioning of R axis.
1): Set the starting point at the current point after the machine is
reset, and make a mark on the cutter head and the cutter
TC-6832
Motion controller user manual
41
2) In the normal standby interface of the panel, click "Settings" in
the lower left corner to enter the high and low setting interface
1", click "Axis
movement" to move down the UD1 axis. When the tool tip is close
to the adsorption table, switch the UD1 axis to slow movement,
when the tool tip is attached the surface of the table, stop moving.
and click "Set Current Position to Low Point". If you are familiar with
the low point of your machine, you can directly modify the low point
4) High point setting: put a small piece of material(which can be
on the surface of the platform,
1", click "axis movement", move the UD1 axis
upward, move the tip of the knife to the top of the material surface,
stop moving, and click "Set Current Position to High Point". If you
igh point of your machine, you can directly
modify the high point data. The distance of the high point must be
greater than the thickness of the material! , It is not advisable to set
the maximum value, this will reduce the cutting efficiency, just set
5) Similarly, the settings of other cutter heads are as in steps 1-4
1): Set the starting point at the current point after the machine is
reset, and make a mark on the cutter head and the cutter seat, as
