Trocen TC-6832 Скачать руководство пользователя страница 35

Страница: 35 / 48

WWW.AWC608.COM

refer to the actual operation for the specific operation)

4: input signal connection

Please connect the corresponding device input according to the

actual needs. The high and low levels of the input port can be set. It
is recommended to connect the input signal (the effective signal is
low level, and the input port is high level 24V in standby). The
signal is the driver alarm signal

5: output connection

Please combine the definition of the output port diagram and

connect to the corresponding output port. All the output ports are
24V high levels during working and 0V while standby. All OUT
ports must be isolated by relays to connect to peripherals, and
cannot be directly connected to OUT ports!

The main OUT port is for vibration, suction and punching of the

cutter head, please install it according to your actual needs.

6. Installation of power supply

The power supply of this system is DC 24 V, please provide a

reliable switching power supply, DC 24V 3A switching power supply
is recommended

7: Connection of system communication

This system supports network and USB communication. Please

use the network cable and USB cable configured with the system to

Motion controller user manual

refer to the actual operation for the specific operation)

4: input signal connection

ct the corresponding device input according to the

ignal is the driver alarm signal

5: output connection

Please combine the definition of the output port diagram and

connect to the corresponding output port. All the output ports are
24V high levels during working and 0V while standby. All OUT

be isolated by relays to connect to peripherals, and

cannot be directly connected to OUT ports!

The main OUT port is for vibration, suction and punching of the

cutter head, please install it according to your actual needs.

6. Installation of power supply

The power supply of this system is DC 24 V, please provide a

reliable switching power supply, DC 24V 3A switching power supply

7: Connection of system communication

This system supports network and USB communication. Please

cable and USB cable configured with the system to

TC-6832

Motion controller user manual

ct the corresponding device input according to the

Please combine the definition of the output port diagram and

connect to the corresponding output port. All the output ports are
24V high levels during working and 0V while standby. All OUT

be isolated by relays to connect to peripherals, and

The main OUT port is for vibration, suction and punching of the

cutter head, please install it according to your actual needs.

The power supply of this system is DC 24 V, please provide a

reliable switching power supply, DC 24V 3A switching power supply

This system supports network and USB communication. Please

cable and USB cable configured with the system to

Содержание TC-6832

















































Результаты поиска

Содержание TC-6832

Отзывы:

Бренды по названию

Популярные бренды

Trocen TC-6832, Руководство по эксплуатации

Результаты поиска

Содержание TC-6832

Отзывы:

Бренды по названию

Популярные бренды