manualshive.com logo in svg

Trocen TC-6832, Руководство по эксплуатации

Поделиться
Скачать
Trocen TC-6832 Скачать руководство пользователя страница 40

                                                                                                             

WWW.AWC608.COM 

 

4) Return to the main interface, press the reset button and wait for 

all  axes  to  reset.  All  axes  can  only  be  moved  by  the  arrow  keys 
when the normal reset is completed. 
the normal reset axis cannot be moved by the arrow keys, including 
resetting the relevant axis in the return interface.

5) Test the button direction, if there is something wrong, enter the 

manufacturer parameters to modify the bu

 
Five:  Commissioning  the  pulse  equivalent  and  the  size  of  the 

common axis. 

1) X-axis Distance Per Pulse commissioning.
1.  Enter  the  manufacturer  parameter  X

【

Distance Per Pulse

2.  According  to  the  prompt  screen,  mov

convenient position for marking, make this point marked as A, and 
click "The first step is set as the starting point"

3. Click "Axis Move" to move the axis to a certain position, mark 

this point as B, and click "Second Set as End Po

4.first measure the actual distance between the AB points with a 

ruler,  and  then  click  "0.00"  in  the  "distance  after  the  third  step 
measurement"; enter the distance to be measured

5. Click "Step 4: Modify Distance Per Pulse " and click "

complete  the  commissioning  of  the  X
value. 

 
2) Similarly, the Distance Per Pulse values of Y axis, UD axis and 

                                                                                                             

Motion controller user manual

 

4) Return to the main interface, press the reset button and wait for 

all  axes  to  reset.  All  axes  can  only  be  moved  by  the  arrow  keys 
when the normal reset is completed. Those that do not complete 
the normal reset axis cannot be moved by the arrow keys, including 
resetting the relevant axis in the return interface. 

5) Test the button direction, if there is something wrong, enter the 

manufacturer parameters to modify the button direction,

Five:  Commissioning  the  pulse  equivalent  and  the  size  of  the 

axis Distance Per Pulse commissioning. 

1.  Enter  the  manufacturer  parameter  X-axis  screen  and  click  "

Distance Per Pulse

】

" 

2.  According  to  the  prompt  screen,  move  the  axis  to  a  certain 

convenient position for marking, make this point marked as A, and 
click "The first step is set as the starting point" 

3. Click "Axis Move" to move the axis to a certain position, mark 

this point as B, and click "Second Set as End Point" on the screen

4.first measure the actual distance between the AB points with a 

ruler,  and  then  click  "0.00"  in  the  "distance  after  the  third  step 
measurement"; enter the distance to be measured 

5. Click "Step 4: Modify Distance Per Pulse " and click "

complete  the  commissioning  of  the  X-axis  Distance  Per  Pulse 

2) Similarly, the Distance Per Pulse values of Y axis, UD axis and 

                                                                                                              TC-6832   

Motion controller user manual

 

 

39 

4) Return to the main interface, press the reset button and wait for 

all  axes  to  reset.  All  axes  can  only  be  moved  by  the  arrow  keys 

Those that do not complete 

the normal reset axis cannot be moved by the arrow keys, including 

5) Test the button direction, if there is something wrong, enter the 

tton direction, 

Five:  Commissioning  the  pulse  equivalent  and  the  size  of  the 

axis  screen  and  click  "

e  the  axis  to  a  certain 

convenient position for marking, make this point marked as A, and 

3. Click "Axis Move" to move the axis to a certain position, mark 

int" on the screen 

4.first measure the actual distance between the AB points with a 

ruler,  and  then  click  "0.00"  in  the  "distance  after  the  third  step 

5. Click "Step 4: Modify Distance Per Pulse " and click "Modify" to 

axis  Distance  Per  Pulse 

2) Similarly, the Distance Per Pulse values of Y axis, UD axis and 

Содержание TC-6832

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды