Triumph Adler DP 773 Скачать руководство пользователя страница 77

Страница: 77 / 113

3PH

1-4-8

1-4-4 Mechanical problems

If the part causing the problem was not supplied, use the unit including the part for replacement.

Problem

Causes/check procedures

Corrective measures

(1)
No primary original
feed.

Check if the surfaces of the following pul-
leys are dirty with paper powder.
DP forwarding pulley
DP paper feed roller

Clean with isopropyl alcohol.

Check if the following pulleys is
deformed.
DP forwarding pulley
DP paper feed roller

Check visually and replace any
deformed (see page 1-5-3).

(2)
Multiple sheets of orig-
inal are fed.

Original is not correctly set.

Set the original correctly.

Check if the DP separation pulley is
worn.

Replace the DP separation pulley if it is
worn (see page 1-5-3).

(3)
Originals jam.

Originals being used do not conform with
the specifications.

Use only originals conforming to the
specifications.

Check if the surfaces of the following pul-
leys are dirty with paper powder.
DP forwarding pulley
DP paper feed roller

Clean with isopropyl alcohol.

Check if the contact between the regis-
tration roller and registration pulley is cor-
rect.

Check visually and remedy if necessary.

Check if the contact between the convey-
ing roller and conveying pulley is correct.

Check visually and remedy if necessary.

Check if the contact between the eject
roller and eject pulley is correct.

Check visually and remedy if necessary.

Check if the contact between the switch-
back roller and switchback pulley is cor-
rect.

Check visually and remedy if necessary.

Содержание DP 773


















































































































Результаты поиска

Содержание DP 773

Отзывы:

Бренды по названию

Популярные бренды

Triumph Adler DP 773, Руководство по обслуживанию

Результаты поиска

Содержание DP 773

Отзывы:

Бренды по названию

Популярные бренды