manualshive.com logo in svg

Triumph Adler DP 773, Руководство по обслуживанию

Поделиться
Скачать
Triumph Adler DP 773 Скачать руководство пользователя страница 59

3PH

1-3-39

U411

Method: [Table (Chart2)]

1. Enter the target values which are shown on the back of the specified original 

(P/N: 302FZ56990) executing maintenance item U425.

2. Set a specified original on the platen.
3. Enter maintenance item U411.
4. Select [Target].
5. Select [U425] and press the start key.
6. Select [Table (Chart2)].
7. Select the item.

8. Press the start key. Auto adjustment starts.

* : When automatic adjustment has normally completed, [OK] is displayed. If a problem 

occurs during auto adjustment, error code is displayed and operation stops. Should this 
happen, determine the details of the problem and repeat the procedure from the begin-
ning.

Method: [DP FaceUp (Chart2)]

1. Measure the leading edge, main scanning, and auxiliary scanning of the specified original (P/

N: 302AC68243) and enter the values by executing maintenance item U425.

2. Set a specified original (P/N: 302AC68243) on the DP. 

Cut the trailing edge of the original.

Figure 1-3-11 

3. Enter maintenance item U411.
4. Select [Target].
5. Select [U425] and press the start key.
6. Select [DP FaceUp (Chart2)].
7. Select [INPUT].

Item No.

Description

Display

Description

All

Executing the all scanner adjustment

Input

Executing the adjustment for magnification, leading edge tim-
ing and center line

C.A.

Executing the adjustment for chromatic aberration filter

MTF

Executing the adjustment for MTF filter

Gamma

Executing the adjustment for input gamma

Matrix

Executing the adjustment for matrix

74 ± 1 mm

149 ± 1 mm

5 mm

Display

Description

Input

Executing the adjustment in the DP scanning section (first 
side) for magnification, leading edge timing and center line

Содержание DP 773


















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды