Triumph Adler DP 773 Скачать руководство пользователя страница 70

Страница: 70 / 113

3PH

1-4-1

1-4 Troubleshooting

1-4-1 Paper mis feed detection

(1) Paper mis feed indication

When a paper misfeed occurs, the machine immediately stops printing and displays the paper misfeed mes-
sage on the operation panel.

To remove original jammed in the optional DP, open the document processor top cover.

Paper misfeed detection can be reset by opening and closing the respective covers to turn safety switch off and on.

The positions and the corrective actions are displayed on the touch panel when a paper jam has occurred.

(2)

Paper mis feed detection condition

Figure 1-4-1

Code

Contents

Conditions

9001

DP original conveying jam

DP timing sensor (DPTS) turns off within the specified time
since the sensor turns on.

9002

DP sensor stay jam

Sensor in the conveying system is on since original feeding
starts.

9004

DP original switchback jam

During duplex switchback scanning, the DP registration sen-
sor (DPRS) does not turn on within specified time of the DP
timing sensor (DPTS) turning off.

9005

No original feed jam 2

DP lift sensor 1 (DPLS1) does not turn on within specified time
of the lift plate rising.

9006

DP switchback jam 3

DP eject sensor (DPES) is not turned on within specified time
since original switchback operation starts.

DPRS

DPTS

DPSBS

DPOS

DPPFS

DPRCL

Содержание DP 773


















































































































Результаты поиска

Содержание DP 773

Отзывы:

Бренды по названию

Популярные бренды

Triumph Adler DP 773, Руководство по обслуживанию

Результаты поиска

Содержание DP 773

Отзывы:

Бренды по названию

Популярные бренды