Triton TC12DBSMS, Инструкция по эксплуатации и безопасности

Страница: 6 / 21

GB
10
GB
11
ROTATING LOWER
BLADE GUARD
The rotating lower
blade guard (12)
provides protection
from both sides of
the blade. It retracts
over the upper blade
guard (9) as the saw is
lowered into the workpiece.
DUST BAG
The dust bag (15)
fits over the dust
extraction port (27).
For more efficient
operation, empty the
dust bag when it is no
more than half full.
This allows better air flow through the bag.
ATTACHING THE SIDE BARS
The side support bars
(36) help to support
the material when
working with long
workpieces. There
are two location holes
(37) for a support bar
on either side of the table. Loosen the lock
screws (38) with the 6mm hex key. Ensure
the side bars are fully inserted before using
them to support the workpiece.
The side support bar
locking screws (38)
must be tightened to
secure the support
bars in position.
TRENCH DEPTH ADJUSTMENT
In its normal position,
the trenching stop (31)
permits the saw blade
to cut right through
a workpiece. When
the saw arm is lifted,
the trenching stop can
be moved to the left
so that the trenching
depth adjustment
screw (30) contacts the
stop as the saw arm is
lowered. This restricts
the cut to a “trench”
in the workpiece. The
depth of the trench
can be adjusted with
the trenching depth
adjustment screw (30)
and locked in position
with the trenching
depth lock nut (32).
TURNING ON AND OFF
1. To turn the saw on
depress and hold the
on/off trigger switch
(24)
2. To turn the saw off
release the on/off
trigger switch (24).
NOTE. To help prevent unauthorized
use the on/off switch features a hole
that allows it to be locked in the off position
using a padlock. To lock the switch in the
off position place the padlock through the
on/off switch and lock it. Remove the key
and store it in a secure place.
Functions
Functions
TURNING ON THE REDEYE
®
LASER LINE GENERATOR
The REDEYE
®
laser
line generator emits 2
intense narrow beams
of pure red light to
guide you as you cut.
It improves operator
cutting vision, enables
faster set-up, increases accuracy and
improves safety. To turn on the laser lines
press the laser light on/off switch (2). To
turn off the laser press the laser light on/off
switch (2) one more time.
SETTING THE TABLE SQUARE
WITH THE BLADE
1. Make sure that the electrical plug is
removed from the power point.
2. Push the saw arm (5) down to its lowest
position and engage the release knob (6) to
hold the saw arm in the transport position.
3. Loosen the mitre
lock (25).
4. Rotate the table
(21) until the pointer
is positioned at 0°.
5. Tighten the mitre
lock (25).
6. Loosen the bevel lock (16) and set the
saw arm (5) at 0 o bevel (the blade at 90°
to the mitre table). Tighten the bevel
lock (16).
7. Place a set square against the table (21)
and the flat part of the blade.
NOTE. Make sure that the square
contacts the flat part of the saw
blade, not the teeth.
8. Rotate the blade by hand and check the
blade-to-table alignment at several points.
9. The edge of the set square and the saw
blade should be parallel.
10. If the saw blade angles away from the set
square, adjust as follows.
11. Use a 13mm wrench or adjustable
wrench to loosen the lock nut securing
the 0° bevel adjustment screw (35).
Also, loosen the bevel lock (16).
12. Adjust the 0° bevel
adjustment screw
(35) with the 6mm
hex key to bring
the saw blade into
alignment with the
square.
13. Loosen the 2 Phillips head screws
holding the pointer of the bevel scale
(17) and adjust the position of the
pointer so that it accurately indicates
zero on the scale. Retighten the screw.
14. Retighten the bevel lock (16) and
the lock nut securing the 0° bevel
adjustment screw (35).
NOTE. The above procedure can
also be used to check the angle of
the saw blade to the table at either 45°
bevel angle to the left or to the right. The
45° bevel adjustment screws (33 & 34)
are on opposite sides of the saw arm. You
will require a 13mm wrench or adjustable
wrench (not supplied) for the lock nut and
the 6mm hex key for the set screws.
90°