background image

Rear Panel 

“REPLACE BATT” LED: This red light will illuminate constantly and the 
UPS alarm will beep every 2 seconds if your UPS’s microprocessor detects a 
battery fault or if your UPS fails the automatic self-test (after you turn your 
UPS ON) and the UPS battery is less than fully charged. Let the UPS system 
charge  for  at  least  12  hours  and  perform  a  self  test  using  the  “ON/TEST 
Button” as described on page 6. If the light continues to stay on, contact Tripp 
Lite for service.
 
 
 
Accessory Slot: Remove the small cover panel from this slot to use optional 
accessories  to  remotely  monitor  and  control  your  UPS.  Contact  Tripp  Lite 
Customer Support at (773) 869-1234 for more information, including a list of 
available SNMP, network management and connectivity products.

External Battery Pack Connector (configuration varies by model): Use to 
connect  optional  Tripp  Lite  Battery  Packs  for  additional  runtime.  Contact 
Tripp Lite Customer Support at (773) 869-1234 for the appropriate Tripp Lite 
battery pack to connect. Refer to instructions available with the Battery Pack 
for complete connection information and safety warnings.

Fan: The fan cools the UPS’s internal components. It is always on when line 
power is present.

Input Circuit Breaker Switch: This resettable breaker prevents high input 
current  from  damaging  the  UPS  or  the  attached  load.  If  this  breaker  trips, 
make sure your UPS is connected to AC power of the proper voltage before 
resetting the circuit breaker by pushing the breaker switch in.

Ground  Screw:  Use  this  to  connect  any  equipment  that  requires  a  chassis 
ground.

Output  Circuit  Breakers  Switches  (HTR22-3U):  These  resettable  circuit 
breakers protect your UPS from output overload. If one or both breakers trip, 
remove some of the load on the circuit(s) and allow the UPS to cool before 
pressing the breaker switch(es) in to reset.

Input Cord: This permanently attached power cord connects your UPS to a 
power outlet.

Front Panel Indicator Lights 

continued

Basic Operation 

(continued)

8

200907169  93-2615.indd   8

8/11/2009   10:15:04 AM

Содержание SmartOnline 2-9USTAND













Отзывы: