Tridonic luxCONTROL DaLI Msensor 5DPI 14 Скачать руководство пользователя | Manualshive

Страница: 12 / 52

background image

Product manual DALI MSensor 5DPI 14 | 06-2017 | 1.1 | en

Description

c

8 / 48

3. Description

The DALI MSensor is a digital controller in the comfortDIM product range that can be used to control the control
gear of a DALI group collectively. The sensor combines three functions in one control device:

The DALI MSensor supports three modes for use in combination with a higher-level DALI master controller:

The DALI MSensor is is available in four different housing designs:

Fitted in luminaire

Recessed into ceiling

Constant light control

_

Presence-based control

_

Remote control

_

Direct master mode

_

Indirect master mode

_

Slave mode

_

I

NOTICE

The following chapters deal with Direct master mode in detail and are only valid for this mode.
In chapter "Enhanced functionality" the other two modes are dealt with briefly.

«
...
10
11
12
13
14
...
»

Содержание luxCONTROL DaLI Msensor 5DPI 14





















































Отзывы:

Нет отзывов

Похожие инструкции для luxCONTROL DaLI Msensor 5DPI 14

Бренд: H3C Страницы: 57

Бренд: Badger Basket Страницы: 3

Бренд: BADLANDS Страницы: 2

Бренд: Calpeda Страницы: 4

Бренд: Campbell Страницы: 34

Бренд: Danfoss Страницы: 7

Бренд: HANYOUNG NUX Страницы: 56

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: NCR Страницы: 8

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды