manualshive.com logo in svg

Trico DR-7, Руководство пользователя

Поделиться
Скачать
Trico DR-7 Скачать руководство пользователя страница 2

Page 2 of 28 

 

Table Of Contents 

1.  Introduction .......................................................................................................................................... 3 
2.  Packing List and Assembly .................................................................................................................... 4 

2.1 – DR-7 Unit Assembly .......................................................................................................................... 4 

3.  Specification and Operating Parameters .............................................................................................. 5 
4.  DR-7 Nomenclature .............................................................................................................................. 6 
5.  Consumables and Accessories .............................................................................................................. 8 
6.  Oil Sample Preparation ......................................................................................................................... 9 

6.1 – Preparing an Oil Sample for Testing ................................................................................................. 9 
6.2 – Dilutions ........................................................................................................................................... 9 

7.  Operating Procedures ......................................................................................................................... 10 

7.1 – RUN DR Tab .................................................................................................................................... 10 

7.1.1 – STANDARD Operation ............................................................................................................. 11 
7.1.2 – OPAQUE Operation ................................................................................................................. 14 
7.1.3 – MENU Button .......................................................................................................................... 16 
7.1.4 –Shutdown Procedures .............................................................................................................. 16 

7.2 – CHARTING Tab ................................................................................................................................ 17 
7.3 – BASELINE Tab ................................................................................................................................. 17 
7.4 – CALIBRATION Tab ........................................................................................................................... 18 

7.4.1 – OPTICAL Calibration ................................................................................................................ 18 

7.4.1.1 – Optical Calibration Check with Trico #DR7-FIL ................................................................. 20 

7.4.2 – END OF OIL Sensor Adjustment .............................................................................................. 21 

7.5 – HELP Tab ......................................................................................................................................... 22 
7.6 – ABOUT Tab ..................................................................................................................................... 22 

8.  Downloading and Understanding DR Data ......................................................................................... 23 

8.1 – Quantifying DR Data ....................................................................................................................... 23 
8.2 – D

L 

and D

S

 Readings ......................................................................................................................... 26 

9.  Maintaining the DR-7 .......................................................................................................................... 27 

9.1 – Sensor Cleasning ............................................................................................................................ 27 

10.  Limited Warranty ................................................................................................................................ 28 

 

Содержание DR-7





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды