Trico DR-7 Скачать руководство пользователя страница 8

Страница: 8 / 28

Page 8 of 28

Consumables and Accessories

It will become necessary to reorder the consumables to continue testing on the DR-7 unit. This section

contains reordering information. Many of the test equipment items should not be reused. Contaminated

devices can cause inaccurate or incorrect interpretation.

Part # 73-0050 Pipette Tips- GLASS (Package of 200) –

Disposable

glass tips

used with the pipettor.

Part # 73-0060 Sample Vials (Package of 250)

– Disposable glass vial holds the oil and heptane and fit

properly into the vial holder.

Part # 73-0090 Sample Vial Rack –

Will hold up to 18 sample vials in preparation for testing.

Heptane –

A filtered solvent used to thin the oil sample for testing to run through the precipitator tube at

a quicker rate. The fixer can be used to clean between the optics assembly and magnet assembly. This

solvent is non-carcinogenic, but flammable. (n-Heptane 99+% for Spectrophotometry can be purchased

from VWR at

https://us.vwr.com

or call 1-800-932-5000)

Part # 74-0020 Diluent Oil –

Used when the oil sample tested exceeds a DL or DS reading of 90 or more

and the sample must be diluted to get a reading under 90 units.

Part # 74-0040 Precipitator Tubes (Package of 250) –

This disposable tube carries the oil sample from

the sample vial, over the magnet assembly to the waste bottle. The precipitator tube is constructed of four

parts. The first is a 33” piece of capillary tubing. This runs into a 4-inch piece of glass and is held in place

by a black shrink tube. A piece of tygon tubing is added to the other end of the glass to connect the glass

tube with the left bulkhead.

Part # 74-0250 Grease Solvent

– An agent used to dissolve grease into a form that can be tested with the

DR-7 unit.

Part # 75-0010 Bottle Top Dispenser, 1 ml –

Use in the fixer bottle to dispense one milliliter of heptane

with each pump.

Part # 75-0030 Pipette Dispenser (Pipettor) –

Used to draw one milliliter of the oil sample for the test.

Part # 75-0040 Pipette Tips- PLASTIC (Package of 250) –

Disposable plastic tips

used with the pipettor.

Part # 76-0030 Wear Particle Atlas –

A guide to wear particle identification containing photographs of

critical wear particles found in used lubricating oil, illustrative case histories, and operational procedures

for wear debris analysis.

Part # 43021 DR-7 Calibration Tube

- Used in calibration procedure to correct unit light intensity

output.

Part # DR-7FIL

- Used for calibration purposes on the DR-7 to confirm the calibration and alignment

readings over time.

NOTE:

Part # 73-0060, Part # 74-0040, and Part # 73-0050

must be discarded after one use in order to

eliminate cross contamination.

CAUTION:

Heptane and Part # 74-0250 Grease Solvent are considered hazardous materials and should

be handled with caution and disposed of properly. Consult the Safety Data Sheet (SDS) enclosed with

these chemicals for more information.

Содержание DR-7





























Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды

Trico DR-7, Руководство пользователя

Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды