Trico DR-7 Скачать руководство пользователя страница 4

Страница: 4 / 28

Page 4 of 28

Packing List and Assembly

After receiving the DR-7, check the package for any shipping damage, and report the damage to the

carrier that delivered the package to you. Shipping damage is the receiver’s responsibility.

Packing items:

1 – DR-7 Direct Reading Ferrograph Unit

1 – Universal Power Cord

1 – Stainless Steel Sample Vial Holder

1 – Spare 1A Fuse

1 – Stainless Steel 125 ml Beaker

1 – DR-7 User’s Manual

3 – Spare “End of Oil Sensor” Doors

1 – Calibration Tube PN: 43021

2.1 – DR-7 Unit Assembly

Required tools for Assembly:

1 – #2 Philips Head Screwdriver

Remove the 125 ml beaker from the packing paper. Place the beaker into the recessed cup for waste

collection.

The drain tube on the right (facing the instrument) bulkhead should be placed into beaker. During

factory conformity testing a test liquid is circulated through the pump tubing to verify function and

check units for leakage. Excess fluid may still be in the tubing upon arrival. After time the drain tube

will become hard and brittle. A new tube can be attached using the tubing cut from a used precipitator

tube as a replacement.

Remove the two screws from the top of the instrument where the vial holder goes. Place the stainless

vial holder on top of the tower with the fingers pointing toward you and thread the two screws back

into the holes at the top left side of the Instrument. Tighten the screws using a #2 Phillips head.

Plug the universal power cord into the back of the DR-7 into the power jack and then into an

electrical outlet.

NOTE:

If the electric supply is other than 120v, 60/50 Hz, the standard Universal Power Cord

provided will need to be replaced or adapted to the host country’s receptacle. Ensure that the power

supplied is within the range outlined in the specifications of this manual. It is the user’s responsibility

to supply the correct plug for the available power. Install the correct plug, then plug the power supply

into the back of the DR-7 and then into the electrical outlet.

To lift and move the DR-7, turn off the instrument and disconnect the power cord and the computer cable,

if attached. Place your hands under the instrument two thirds of the way back and lift. This will balance

the instrument while lifting.

Содержание DR-7





























Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды

Trico DR-7, Руководство пользователя

Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды