Trico DR-7 Скачать руководство пользователя страница 5

Страница: 5 / 28

Page 5 of 28

Specification and Operating Parameters

Physical Specifications

Length (Front to Back):

9.00 in.

22.8 cm

Width (Side to Side):

12.00 in.

30.5 cm

Height:

19.75 in.

50.2 cm

Weight (Instrument Only):

13 lbs.

5.9 kg

Power

Voltage: 100-240V AC

Frequency: 50/60 Hz

Amperage: 1A

Instrument contains a 1A power fuse located at the power plug inlet

Hardware

Operating system: Windows 10 IoT

Memory: 64 GB Flash

External USB Ports: 2 x USB “A”

Ethernet Connection: RJ45 cat 5

RAM: 4 GB DDR2 RAM

Processor: Intel® Celeron® CPU N2807 @ 1.58 Ghz

Environmental Conditions

For indoor use on a solid level surface without movement or vibration.

Use in a well-ventilated area.

Room temperature:

50ºF to 85ºF

10ºC to 29ºC

Humidity: 5% to 50% non-condensing

CAUTION:

DO NOT operate the DR-7 with the back panel removed. Unplug the DR-7 from the power

supply before removing the back panel for adjustments. Check with Trico before removing as this could

void the unit warranty. All other repairs must be done at the factory

Содержание DR-7





























Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды

Trico DR-7, Руководство пользователя

Результаты поиска

Содержание DR-7

Отзывы:

Бренды по названию

Популярные бренды