Operation - TV Mode
Press any button on TV remote control
to turn on the switched outlets.
Press power on TV remote control to
turn on TV.
Use peripheral RF/IR remotes to turn
on peripherals as needed.
Step 2
Step 1
Step 3
When done watching TV, press the
power button on the TV remote control
to switch off the TV. All switched outlets
will then automatically turn off within
one minute.
Step 4
ON
OFF
www.tricklestar.com
Advanced Pow
Advanced
Pow
Outlet
7
Energy Saving
Countdown Timer Operation
For the first 15 / 30 / 60 minutes - the multi-sensor senses for RF/IR only
For the next 15 / 30 / 60 minutes - the multi-sensor senses for RF/IR signal or
movement
After 30 / 60 / 120 minutes if no RF/IR or movement has been
sensed the switched outlets willl switch off automatically.
Switched Outlets
Switch On
User Switches
TV On
15, 30, 60 min Countdown
Timer
Starts
RF + IR Remote Control Button
Press Detected?
Next 15, 30, 60 min Countdown
Timer Starts
RF/IR Or Movement
Detected
TV + Peripherals
Switch Off
No
No
Yes
Yes
ALERTS START
10 min Before Countdown
Timer Expiry
Buzzer Sounds 3X
LED Flashes
Terms
IR
IR Signal Sensor
PIR Sensor
Movement
Countdown Timer
Countdown Period
LED
Buzzer
Infrared signal, transmitted by a remote control
Multi-sensor senses for an IR command
Multi-sensor
uses passive Infrared sensing to
detect movement
Movement detected by PIR
Time before the switched outlets are automatically
switched off
30 minutes / 60 minutes (default) / 120 minutes
Red LED located in multi-sensor
When IR or movement is sensed, the LED will flash
Buzzer located in the multi-sensor
-
RF
Radio frequency, transmitted by a remote control
-
-
-
-
-
-
-
-
-
User Presses RF/IR
Remote Control
4
5
Ground LED
When illuminated, it indicates that the Product is correctly grounded.
If not illuminated, there is a grounding problem and you must contact an
electrician to properly ground the socket. Surge protection will not work with an
improperly grounded outlet.
Surge LED
When illuminated, it indicates that the surge protection is functioning normally.
If this LED illuminates red or extinguishes at any time, the Product was
sacrificed to protect your devices and must be replaced.
6
7
Switched Outlets LED
When illuminated, it indicates that the switched outlets are receiving power.
Resettable Circuit Breaker
All outlets on the Product are protected. If the surge, ground, and switched
LEDs are not illuminated and/or connected devices are not receiving power,
switch the circuit breaker to activate power.
8
Always-On Outlets
Equipment that requires continuous power should be plugged into the
always-on outlets.
9
< tv > Outlet
The outlet marked <tv> is the control outlet and includes true RMS power
measurement.
IMPORTANT
THE TV MUST BE PLUGGED INTO THIS OUTLET
Switched Outlets
If there is no RF, IR, or motion detected, these outlets will switch off.
1
2
3
RF/IR + Movement Multi-Sensor
The Zigbee multi-sensor is connected to the powerstrip via the RJ11 port
marked “sensor.” Mount the ZigBee multi-sensor on the underside of the TV,
near the IR receiver on the TV (typically located next to the TV's power on/off
button). The multi-sensor must be located within line of sight of where you
normally use your remote controls.
Power Connection
The Product must only be plugged into a grounded receptacle for surge
protection to operate correctly. All connected devices should be plugged
directly into the Product. Use of an extension cord, adaptor or other powerstrip
in conjunction with the Product will void all warranties.
Sensor/RJ11 Port
Plug the RF/IR & motion multi-sensor into this port.
There will be a soft audible ‘click’ when the connector is inserted correctly.
www.tricklestar.com
Advanced Pow
Advanced
Pow
Outlet
7
Product Overview
4 5 6
7
9
8
1
2
3
10
10
