manualshive.com logo in svg

TriangleTube Prestige Slol 250, Руководство по установке и обслуживанию

Поделиться
Скачать
TriangleTube Prestige Slol 250 Скачать руководство пользователя страница 47

41

Start-Up Procedures

c

Check Vent Piping and Combustion Air
Piping.

Check for gas-tight seal at every con-
nection and seam of the venting and
combustion air piping.

Venting system must be sealed gas-tight

to prevent flue gas spillage and potential

carbon monoxide emissions, which will

result in severe personal injury or death.

c

Check Gas Piping

Check around the unit for gas odor fol-
lowing the procedure outlined in this
manual on Page 39.

If any gas leaks are found or suspected,

shut the unit down immediately.  Use a

gas detection device or bubble test to

locate the source of the gas leak and

repair at once.  Do not operate the unit

until the leak is corrected.  Failure to

comply with this procedure could result

in severe personal injury, death or sub-

stantial property damage.

c

Verify Flame Pattern and Combustion

Check the flame pattern through the
inspection port of the heat exchanger.
The flame should be blue and stable.
The flame should be the length of the
burner head openings.

The combustion testing and adjustments

must be performed by a qualified

installer, service agency or the gas suppli-

er. All combustion measurements must be

performed with calibrated equipment to

ensure proper reading and accuracy.

Test for CO2 or O2 and for CO during
high firing rate.  To manually place the
boiler into high fire mode, reference
page 45. The combustion reading
should be within the range listed in
Table 2.  

The CO level should not

exceed 100 ppm when combustion is

correct.

The combustion levels should be mea-

sured at high firing rate, refer to page 45

of the PRESTIGE Solo control section

on how to set the firing rate. If the com-

bustion levels are not within the range

given in Table 2 for the firing rate, shut

the boiler down and contact Triangle

Tube Engineering Department. Failure

to comply with this requirement could

result in severe personal injury, death or

substantial property damage.

c

Measure Input - Natural Gas Only

1. Ensure the boiler is firing at maximum firing

rate. To manually place the boiler into high
fire mode, reference page 45.

2. Operate the unit for approximately 10

minutes.

3. Turn off all gas appliances within the build-

ing, except the PRESTIGE Solo.

4. At the gas meter, record the time required

to use one cubic foot of gas.

WARNING

WARNING

WARNING

WARNING

Table 2:  Recommended Combustion Levels

Содержание Prestige Slol 250


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды