manualshive.com logo in svg

TriangleTube Prestige Slol 250, Руководство по установке и обслуживанию

Поделиться
Скачать
TriangleTube Prestige Slol 250 Скачать руководство пользователя страница 37

31

Internal Wiring

SECTION VII - Internal Wiring

ELECTRICAL SHOCK HAZARD.  For

your safety, disconnect electrical power

supply to the unit before servicing or

making any electrical connections to

avoid possible electric shock hazard.

Failure to do so can cause severe person-

al injury or death.

Prior to servicing, label all wires before

disconnecting. Wiring errors can cause

improper and dangerous operation.

Verify proper wiring and operation after

servicing.

General Requirements

-

Wiring must be N.E.C Class 1.

-

If original wiring as supplied with the unit
must be replaced, use only Type T 90ºC
wire or equivalent as a minimum.

-

The PRESTIGE Solo  must be electrically
grounded as required by National
Electrical Code ANSI/NFPA 70 - latest edi-
tion and / or the Canadian Electrical Code
Part 1, CSA C22.1, Electrical Code.

Control Module Circulator AMP Ratings

-

AMP draw of the CH circulator not to
exceed 2 amps.

-

AMP draw of the DHW circulator not to
exceed 2 amps.

Wiring Tool Instructions

1.   Locate the wiring tools on the PRESTIGE

Solo just below the MCBA control in a
plastic bag and below the extra fuses.

2.  Locate the terminal blocks on the PRES-

TIGE Solo below the MCBA control.

The 120V Terminals are located on the

left set of Terminal Blocks. The 24V

Terminals are located on the right set of

terminal blocks.

3.  Carefully pull down on the lower half of

the terminal block to remove.

4.   Hook the wiring tool into the desired slot of

the terminal block as shown in Fig.19.

5.   Push wiring tool in towards the terminal

block and insert wire in slot at bottom of
terminal block.

6.   Repeat steps 4 & 5 until all wiring is com-

plete.

7.  Re-connect the lower half of the terminal

block to the upper half.

8.   Place the wiring tool  back into the plastic

bag or leave tool hooked to a slot on the
24V terminal block.

When wiring the PRESTIGE Solo allow

additional length of wire for the access

panel to swing open during servicing.

BEST PRACTICE

NOTICE

CAUTION

WARNING

Terminal Block

Wiring Tool

Fig. 19:  Using the Wiring Tool on the

Terminal Blocks

Содержание Prestige Slol 250


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды