manualshive.com logo in svg

TriangleTube Prestige Slol 250, Руководство по установке и обслуживанию

Поделиться
Скачать
TriangleTube Prestige Slol 250 Скачать руководство пользователя страница 45

39

Start-Up Preparation

Check For Gas Leaks

Prior to start-up and during initial opera-

tion, smell near the floor and around the

unit for gas odorant or any unusual odor.

Do not proceed with the start-up if there

is any indication of a gas leak.  Any leaks

found must be repaired immediately.

Propane installations only - The propane

supplier mixes an odorant with the

propane to make its presence detectable.

In some cases the odorant can fade and

the gas may no longer have an odor.
Prior to start-up of the unit and periodi-

cally after start-up have the propane

supplier check and verify the odorant

level.

Check Thermostat Circuit

-

Disconnect the external thermostat wires
from the 24V terminal strip on the wiring
panel.

-

Connect a voltmeter across the wire ends of
the external thermostat wiring.

-

Close each thermostat, zone valve and
relay in the external circuit one zone at a
time and check the voltage reading across
the wire ends.

-

There should 

NEVER

be voltage measured

at the wire ends.

-

If voltage is measured at the panel under any
condition, check and correct the external
wiring.

In systems using 3-wire zone valves,

backfeed of voltage to the unit is a com-

mon problem.  Use an isolation relay to

prevent voltage from the external circuit

entering the PRESTIGE Solo control

panel.

-

Reconnect the external thermostat
wires to the 24V terminal strip on the
wiring panel.

Inspection of Condensate Drain Assembly

1.  Inspect and ensure the Condensate Drain

Assembly is properly installed as described
on page 25 and shown in Fig. 15 on page
26.

2.  Remove the plug from the Condensate

Drain Assembly and fill with fresh water.

The condensate drain assembly must be

filled with water when the PRESTIGE

Solo is in operation.  The condensate

drain assembly prevents flue gas emis-

sions from entering the condensate line.

Failure to ensure trap is filled with water

could result in severe personal injury or

death.

3.  Re-Install plug in condensate drain assem-

bly.

NOTICE

NOTICE

WARNING

WARNING

Содержание Prestige Slol 250


























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды