Trianco EuroStar Band A Скачать руководство пользователя страница 2

 

HEALTH AND SAFETY 

 

INFORMATION FOR THE USER, INSTALLER AND SERVICE ENGINEER 

 

 

Under  the  Consumer  Protection  Act  1987  and  the  Health  and  Safety  at  Work  Act  1974,  it  is  a 
requirement to provide information on substances hazardous to health (COSHH Regulations 1998). 
 
TR Engineering takes every reasonable care to ensure that its products are designed and constructed to 
meet  these  safety  requirements  when  the  products  are  properly  installed  and  used.  To  fulfil  the 
requirements, products are comprehensively tested and examined before despatch. 
 
When  working  on  the  appliance,  it  is  the  responsibility  of  the  user  or  engineer  to  ensure  that  personal 
protective  clothing  or  equipment  appropriate  to  parts  that  could  be  considered  hazardous  or  harmful  is 
worn. 
 
This appliance may contain some of the items below:

 

 
Insulation and Seals 
 

Glass rope, mineral wool, insulation pads, ceramic fibre and glass insulation. 
 
When handling, avoid inhalation and contact with eyes. These may be harmful and cause irritation to the 
skin, eyes, nose or throat. Use disposable gloves, facemasks and eye protection. 
 
After handling, wash hands and other exposed areas. When disposing of materials, limit dust and the risk 
of inhalation by using a water spray. Ensure materials are securely wrapped. 
 
Seek  urgent  medical  attention  if  inhaled  or  ingested.  Exposure  to  eyes  and  skin  should  be  followed  by 
immediate cleansing of the affected areas and medical attention if necessary. 
 

Glues, Sealants and Paints 
 

The  glues,  sealants  and  paints  used  present  no  known  hazards  when  the  appliance  is  used  in  the 
manner for which it is intended. 
 

Mineral Oils 

 
The appliance is designed to run on 28 sec. Kerosene class C2. The effects of mineral oils on  the skin 
will vary depending on the length of exposure. 
 
Avoid  any  skin  contact  with  oil  or  clothing  contaminated  with  oil.  Kerosene  will  remove  the  protective 
grease normally present on the surface of the skin, rendering it dry, liable to cracking and more prone to 
damage caused by cuts and abrasions. Seek immediate medical attention for any rash, wart or sore that 
develops on any part of the body. 
 
Barrier  cream  that  contains  lanolin,  such  as  Rosalex  Antisolv  is  recommended  together  with  a  strict 
regime of personal cleaning. 
 
Do  not  breathe  oil  vapours.  Do  not  fire  the  burner  in  the  open  (i.e.  out  of  the  boiler),  as  a  misfire  will 
produce unburned oil vapours. Under no circumstances should mineral oils be taken internally. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание EuroStar Band A





































Отзывы: