TRI tool BEVEL MASTER 208B Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 58

background image

21

Model 208B BEVELMASTER

®

92-1482 Rev. 190410

5.4 ADJUSTMENT OF THE TORQUE ACCEPTANCE KEYS

1. Adjusting the torque acceptance keys is required if the BEVELMASTER

®

is

loose radially on the mandrel shaft. This may appear as chatter in the tool bit.

2. Loosen the cap screws in both torque acceptance keys.
3. Rotate the set screw as required until the torque acceptance keys are riding

snugly in the slots in the mandrel shaft.

4. Run the Feed in and out to insure that the torque acceptance keys are not so

tight that the feed is impaired.

5. Re-tighten the cap screws to retain the new settings.
6. Rotate the feed handle clockwise to engage the feed nut with the thread on

the mandrel shaft.

7. A minimum of ten (10) threads must be engaged to prevent the thread from

being stripped during the machining operation.

Mandrel Shaft

Torque Acceptance Key

Cap Screw

Set Screw

Feed Housing

Figure: 7. Adjusting the Torque Acceptance Keys

«
...
21
22
23
24
25
...
»

Содержание BEVEL MASTER 208B



























































Отзывы:

Нет отзывов

Похожие инструкции для BEVEL MASTER 208B

Бренд: Balcrank Страницы: 12

Бренд: Mafell Страницы: 12

Бренд: Mafell Страницы: 142

Бренд: Parkside Страницы: 64

Бренд: Parkside Страницы: 44

Бренд: Parkside Страницы: 64

Бренд: Taylor Страницы: 21

Бренд: RIDGID Страницы: 40

Бренд: Felder Страницы: 10

Carlyle Tools 6-711A

Бренд: Napa Страницы: 16

Бренд: Tryton Страницы: 48

Бренд: Wacker Neuson Страницы: 38

Бренд: Wel-Bilt Страницы: 5

Бренд: Kärcher Страницы: 284

Бренд: Telestar Страницы: 2

Бренд: Fohrenbach Страницы: 8

Бренд: Hot Screen Страницы: 76

CERTI-CRIMP II 2381707-1

Бренд: TE Connectivity Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды