manualshive.com logo in svg

Tri-Clover Tri-Flo CL Series, Руководство по обслуживанию и установке

Поделиться
Скачать
Tri-Clover Tri-Flo CL Series Скачать руководство пользователя страница 2

- 2 -

CONTENTS

Thank you for purchasing a Tri-Clover Product!

This manual contains disassembly and assembly instructions, maintenance procedures,
troubleshooting, and a complete parts list for all CL Series Centrifugal Pumps designed and
manufactured by Tri-Clover Inc., Kenosha, Wisconsin.

READ THIS MANUAL carefully to learn how to service these pumps.  Failure to do so could
result in personal injury or equipment damage.

SAFETY

DO'S AND DON'TS ........................................................................................................................... 3
IMPORTANT SAFETY INFORMATION ............................................................................................ 4

TECHNICAL  INFORMATION

TECHNICAL DATA ............................................................................................................................ 5

INSTALLATION

UNPACKING EQUIPMENT ............................................................................................................... 6
INSTALLATION ................................................................................................................................. 7
OPERATIONAL CHECK ................................................................................................................... 8

MAINTENANCE

CLEANING AND REPAIR ................................................................................................................. 9

MAINTENANCE

DISASSEMBLY ................................................................................................................................. 10
INSPECTION .................................................................................................................................... 15
ASSEMBLY ....................................................................................................................................... 15

TROUBLESHOOTING

TROUBLESHOOTING ...................................................................................................................... 26

PARTS  LIST

ORDERING INFORMATION ............................................................................................................. 28
EXPLODED VIEW ............................................................................................................................ 29
CROSS SECTIONAL VIEW .............................................................................................................. 30
CL PUMP REPLACEMENT PARTS .................................................................................................. 32
CL PUMP REPLACEMENT PARTS .................................................................................................. 33
CL PUMP REPLACEMENT PARTS .................................................................................................. 34
CL PUMP REPLACEMENT PARTS .................................................................................................. 35
SEAL REPLACEMENT PARTS  - TYPE DG (EXTERNAL BALANCED SEAL) ................................ 36
SEAL REPLACEMENT PARTS  - TYPE FG (WATER COOLED SINGLE SEAL) ............................ 37
SEAL REPLACEMENT PARTS  - TYPE EG (WATER COOLED, BALANCED DOUBLE SEAL) ..... 38
SEAL REPLACEMENT PARTS  - JOHN CRANE DOUBLE 8 SEAL ................................................ 39

Содержание Tri-Flo CL Series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды