Tri-Clover DS3218 Скачать руководство пользователя страница 17

Страница: 17 / 20

PROBLEM

Excessive
power
consumption.

Tri-Blender is
noisy.

Excessive
vibration.

Tri-Blender
leaks.

PROBABLE CAUSE

High viscosity with screen in
head.

Magnetic hum in motor.

Motor bearings are worn.

Tri-Blender bearings are worn.

Foreign matter is rotating with
impeller.

Blender is not leveled properly.

Impeller is damaged.

Foreign matter in casing.

Seal failure.

Casing gasket worn or
damaged.

REMEDY

Remove screen.

Install discharge pump on discharge end
of the Tri-Blender.

Consult motor manufacturer.

Replace bearings.

Remove casing and remove foreign
matter - inspect for damage.

Check supply flow to blender.

Level blender.

Replace impeller.

Remove casing and remove foreign
matter - inspect for damage.

Replace seal.

Replace gasket.

TROUBLESHOOTING

Содержание DS3218





















Результаты поиска

Содержание DS3218

Отзывы:

Похожие инструкции для DS3218

Бренды по названию

Популярные бренды

Tri-Clover DS3218, Руководство по обслуживанию и установке

Результаты поиска

Содержание DS3218

Отзывы:

Похожие инструкции для DS3218

Бренды по названию

Популярные бренды