TRENDnet TPE-3012LS Скачать руководство пользователя страница 8

Страница: 8 / 187

TRENDnet User’s Guide

TPE-3012LS / TPE-3018LS

10/100Mbps.

Blinking

: When the Link/ACT LED is blinking, the port is

transmitting or receiving data on the Ethernet
network.

Off

: No link.

SFP Slots (11-12)

Green on

: When the mini-GBIC Green LED lights on, the

respective port is inserted mini-GBIC Gigabit

module.

Green blinking : When the mini-GBIC Green LED is blinking, the port

is transmitting or receiving data on the Gigabit

network.

Amber on

When the mini-GBIC Amber LED lights on, the

respective port is inserted mini-GBIC 100Mbps

module.

Amber blinking When the mini-GBIC Amber LED is blinking, the

port is transmitting or receiving data on the

Ethernet network.

Off

No link

TPE-3018LS

Rear View

•

AC Power Connector

–

Connect the AC power cord to the connector and the

other side into a power outlet. (Input: 100~240VAC, 50/60Hz)

Front View

•

4-Digit 7-Segment Display -

Displays total power, available power, and

power consumption per port using the toggle button.

•

Reset Button

–

Press and hold this button for 10 seconds and release to

reset the switch to factory defaults.

•

PoE+ Gigabit Ports (1-16)

–

Connect PoE and non-PoE network devices.

•

Gigabit Ports (17-18)

–

Connect non-PoE devices or uplinks. Disabled if

SFP slots

17F

18F

are used.

•

SFP Slots Shared (17F-18F)

–

Supports optional 1000BASE-SX/LX mini-

GBIC modules.

AC Power Connector

Gigabit

Ports

PoE+ Gigabit

Ports

Reset

Button

Diagnostic

LEDs

SFP

Slots

4-Digit

Display

Содержание TPE-3012LS




























































































































































































Результаты поиска

Содержание TPE-3012LS

Отзывы:

TRENDnet TPE-3012LS, Руководство пользователя, Страница: 8 / 187

Результаты поиска

Содержание TPE-3012LS

Отзывы: