Trejon OPTIMAL UPX Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 44

Trejon OPTIMAL UPX Series Скачать руководство пользователя страница 32

Instruction manual TREJON OPTIMAL UPX plough (2010)

32

3.9 Road transport

Warning!
Take great care during road transport.

Warning!
Lift the plough to a sufficient height and check the condition of the plough prior
to road transport. Reduce your speed if there are bumps in the road. Too high
a speed can damage the plough.

Warning!
It is the operator’s responsibility to ensure compliance with the relevant country’s
traffic regulations and laws.

3.10 Disconnection of the plough

1) Lower the plough onto a flat surface so that it rests on the support plates.

2) Turn off the tool carrier, apply the parking brake

3) Relieve the load on the hydraulic system so that it is depressurised.

4) Disconnect the hydraulic hoses and protect the couplings with plugs. Anchor these in

the holder.

5) Disconnect the spiral cable.

6) Loosen t

he plough’s attachment.

7) Back the tool carrier away.

If the plough is to remain unused for an extended period, clean it and lubricate all lubrication
points, see section 4.4.

«
...
30
31
32
33
34
...
»

Содержание OPTIMAL UPX Series













































Отзывы:

Нет отзывов