Transcell Technology TI-1520 Скачать руководство пользователя страница 3

 

INTRODUCTION 

 

The  TI-1520  Digital  Indicator  is  a  general  purpose,  industrial  grade  weight  indicator.  One  model  is 
currently available, distinguishable by display type, enclosure type and power supply. Table 1 shows the 
TI-1520 product matrix. 
 
This model can readout up to 50,000 display divisions and can supply enough current for up to 8-350

 

load cells. All setup parameters may be entered via the front panel keys, including calibration. 
 
If your Model TI-1520 Digital Indicator is part of a complete floor scale or has already been installed for 
you,  you  may  skip  to  the  operating  instructions.  Prior  to  using  the  indicator,  please  read  this  chapter 
carefully and completely.  Store the manual in a safe and convenient place so it will be available if you 
have questions concerning the operation of the scale.  

 

MODEL 

DISPLAY  

TYPE 

ENCLOSURE 

TYPE 

POWER SOURCE 

TI-1520 

LED 

Stainless Steel 

100-240 VAC, 50/60 Hz 30W 

TABLE 1: TI-1520 Product Matrix 

 
 
 

FCC NOTE 

 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help. 

 

 

©Transcell Technology, Inc. 2009-2012. All rights reserved. 

The information contained herein is the property of Transcell Technology and is supplied without liability for errors or omissions. No part 
may be reproduced or used except as authorized by contract or other written permission. The copyright and the foregoing restriction on 
reproduction and use extend to all media in which the information may be embodied. 
 
Contents subject to change without notice. 
 
975 Deerfield Parkway   Buffalo Grove, IL 60089 
Tel (847) 419-9180   Fax (847) 419-1515 
http://www.transcell.com 
 

Содержание TI-1520




























Отзывы: