Diagnostics
116
RT-SVX34F-EN
TR-200 VFD Programming
Parameters
Units shipped with an optional variable frequency drive
(VFD) are preset and run tested at the factory. If a problem
with a VFD occurs, ensure that the programmed
parameters listed in
Table 85
have been set before
replacing the drive.
Note:
Model TR-200—Check to make sure that parameter
1-23 is set to 60 Hz. To check parameter 1-23 press
the [Main Menu] button (press [Back] button if the
main menu does not display), use the [
▼
]
button
to scroll down to Load & Motor, press OK, use the
[
▼
] button to select 1-2, press OK, and finally use
the [
▼
] button until parameter 1-23 is displayed.
Parameter 1-23 can then be modified by pressing
OK button and using
[
▲
] and [
▼
]
buttons. When
the desired selection has been made, press the OK
button.
Should replacing the a VFD become necessary, the
replacement is not configured with all of Trane's operating
parameters. The VFD must be programmed before
attempting to operate the unit.
To verify and/or program a VFD, use the following steps:
1.
Remove the mode input (RTRM J6-2 and J6-4) or turn
the NSB panel to OFF so that the fan will not attempt to
start during programming.
HIGH VOLTAGE IS PRESENT AT TERMINAL BLOCK 1TB1
OR UNIT DISCONNECT SWITCH 1S14.
2. To modify TR-200 parameters:
a. Press Main Menu button (press [Back] button if the
main menu does not display)
b. Use the [
▲
] and [
▼
] buttons to find the parameter
menu group (first part of parameter number)
c. Press [OK]
d. Use [
▲
] and [
▼
] buttons to select the correct
parameter sub-group (first digit of second part of
parameter number)
e. Press [OK]
f. Use [
▲
] and [
▼
] buttons to select the specific
parameter
g. Press [OK]
h. To move to a different digit within a parameter
setting, use the [
►◄
] buttons (Highlighted area
indicates digit selected for change)
i. Use [
▲
] and [
▼
] buttons to adjust the digit
j. Press [Cancel] button to disregard change, or press
[OK] to accept change and enter the new setting
3. Repeat step two for each menu selection setting in
Table 85, p. 116
.
4. To reset TR-200 programming parameters back to the
factory defaults:
a. Go to parameter 14-22 Operation Mode
b. Press [OK]
c. Select “Initialization”
d. Press [OK]
e. Cut off the mains supply and wait until the display
turns off.
f. Reconnect the mains supply - the frequency
converter is now reset.
Table 85. Supply and exhaust fan VFD programming
parameters for model TR-200
Menu
Para-
meter
Descrip
tion
Setting
Description
Load &
Motor
1-21
Motor
Power
Set Based
on Motor
Nameplate
Set only for applications
using 3hp Hi-Efficiency
motors. Set to 2.2 kW/3 hp.
1-22
Motor
Voltage
Set Based
on Motor
Nameplate
Set only for 200/230v 60hz
& 380/415 50hz
applications
1-24
Motor
Current
Set Based
on Motor
Nameplate
Sets the motor FLA
1-25
Motor
RPM
Set Based
on Motor
Nameplate
Sets the motor RPM
Limits
and
Warnings
4-18
Current
Limit
100%
Rated
Current
Limits the maximum
current to motor
WARNING
Hazardous Voltage w/Capacitors!
Disconnect all electric power, including remote
disconnects before servicing. Follow proper lockout/
tagout procedures to ensure the power cannot be
inadvertently energized. For variable frequency drives
or other energy storing components provided by Trane
or others, refer to the appropriate manufacturer’s
literature for allowable waiting periods for discharge of
capacitors. Verify with an appropriate voltmeter that all
capacitors have discharged. Failure to disconnect power
and discharge capacitors before servicing could result
in death or serious injury.
For additional information regarding the safe discharge
of capacitors, see PROD-SVB06A-EN
