manualshive.com logo in svg

Trane Tracer UC400, Инструкция по установке, эксплуатации и обслуживанию


Поделиться
Скачать
background image

BAS-SVX065E-EN

51

Operational Causes and Diagnostics

Table 18.

UC400 controller diagnostic causes and diagnostics

Probable Cause

Diagnostic

Fan Not Energizing

Unit Wiring

The wiring between the UC400 Controller outputs, fan relays, and contacts must be present and correct for
normal fan operation.

Failed End Device

The fan motor and relay must be checked to ensure proper operation.

Normal Operation

The fan turns OFF when:

•

The UC400 Controller receives a communicated off signal.

•

The fan-speed switch is set to OFF if no communicated value is present.

•

Specific diagnostics are generated.

•

The default fan speed is set to OFF and the fan is operating in the Auto mode.

If the UC400 Controller is in unoccupied mode, the fan cycles between OFF and the highest fan speed.

No power to the
Controller

If the UC400 Controller does not have power, the unit fan does not operate. For the unit to operate normally, it
must have an input voltage of 24 Vac. If the Marquee/Power LED is OFF continuously, the controller does not
have sufficient power or has failed.

Diagnostic Present

Several diagnostics affect fan operation.

Unit Configuration

The UC400 Controller must be properly configured based on the actual installed end devices and application. If
the unit configuration does not match the actual end device, the fans may not work correctly.

Random Start Observed

After power-up, the UC400 Controller always observes a random start from 5 to 30 seconds. The unit remains
OFF until the random start time expires.

Cycling Fan Operation/
Continuous

The UC400 Controller continuously operates the fan when in the occupied, occupied standby, or occupied
bypass mode. When the controller is in the unoccupied mode, the fan is cycled between high speed and OFF
with capacity.

Unoccupied Operation

Even if the UC400 Controller is configured for continuous fan operation, the fan normally cycles with capacity
during unoccupied mode. While unoccupied, the fan cycles ON or OFF with heating/cooling to provide varying
amounts of heating or cooling to the space.

Fan Mode Off

If a local fan mode switch determines the fan operation, the OFF position controls the fan to off.

Requested Mode Off

The user can communicate a desired operating mode (such as OFF, heat, and cool) to the controller. If OFF is
communicated to the UC400 Controller, it controls the fan to off. There is no heating or cooling.

Isolation Valves Remain Closed

Unit Wiring

The wiring between the UC400 Controller outputs and the valve(s) must be present and correct for normal
valve operation. Refer to applicable wiring diagram.

Failed End Device

The valves must be checked to ensure proper operation.

No power to the
Controller

If the UC400 Controller does not have power, the unit valve(s) will not operate. For the controller to operate
normally, apply an input voltage of 24 Vac. If the Marquee/Power LED is OFF continuously, the unit does not
have sufficient power or has failed.

Diagnostic Present

Several diagnostics affect valve operation. For detailed information about these diagnostics, refer to Table 13,
p. 46.

Normal Operation

The UC400 Controller opens and closes the valves to meet the unit capacity requirements.

Unit Configuration

The UC400 Controller must be properly configured based on the actual installed end devices and application. If
the unit configuration does not match the actual end device, the valves may not work correctly.

Random Start Observed

After power-up, the UC400 Controller always observes a random start from 5 to 30 seconds. The controller
remains OFF until the random start time expires.

Requested Mode Off

The user can communicate a desired operating mode (such as OFF, heat, and cool) to the UC400 Controller. If
OFF is communicated to the unit, the controller controls the fan to off. There is no heating or cooling.

Содержание Tracer UC400





























































Отзывы:

Нет отзывов

Похожие инструкции для Tracer UC400

Nidec Leroy-Somer R180 Installation And Maintenance Manual preview
Leroy-Somer R180
Бренд: Nidec Страницы: 20
Falcon RS500 Owner'S And Installer'S Manual preview
RS500
Бренд: Falcon Страницы: 3
OBaby Cobra Instructions For Use Manual preview
Cobra
Бренд: OBaby Страницы: 47
CAME Z Series Instruction Manual preview
Z Series
Бренд: CAME Страницы: 12
CAME Z Series Technical Documentation Manual preview
Z Series
Бренд: CAME Страницы: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Бренд: Ultrak Страницы: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Бренд: Zander Aachen Страницы: 10
Yudian AI Series Operation Instruction Manual preview
AI Series
Бренд: Yudian Страницы: 26
Daikin ALTHERMA User Manual preview
ALTHERMA
Бренд: Daikin Страницы: 5
ZKTeco F6 Installation Manual preview
F6
Бренд: ZKTeco Страницы: 2
FASAR ELETTRONICA FE230 Quick Start Manual preview
FE230
Бренд: FASAR ELETTRONICA Страницы: 2
Faro Barcelona 33929 Installation Manual preview
33929
Бренд: Faro Barcelona Страницы: 8
Faro 33928 Installation Manual preview
33928
Бренд: Faro Страницы: 3
YASKAWA G7 Series Technical Manual preview
G7 Series
Бренд: YASKAWA Страницы: 456
YOKOGAWA UTAdvanced UT35A Technical Information preview
UTAdvanced UT35A
Бренд: YOKOGAWA Страницы: 18
Haes ELAN HS-5100 User Manual preview
ELAN HS-5100
Бренд: Haes Страницы: 42
mikroElektronika ETH WIZ click Quick Start Manual preview
ETH WIZ click
Бренд: mikroElektronika Страницы: 3
Window Master WMU 831 Installation Instructions Manual preview
WMU 831
Бренд: Window Master Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды