Trane GGAA, Инструкция по установке, эксплуатации и обслуживанию

Страница: 31 / 60

MUA-SVX005B-EN 31
7. With burner drawer removed from duct furnace, inspect the inside surfaces of the heat
exchanger. Wire brush if necessary.
8. Remove any dirt, dust or other foreign matter from the burners using a wire brush and/or
compressed air. Insure all parts of the burner are unobstructed. Inspect and clean pilot burner
if necessary.
9. Reassemble the duct furnace by replacing all parts in order.
10. Light unit per the unit lighting instructions.
11. Check the burner adjustment. See the “Primary Air Shutter Adjustment,” p. 27 section of this
manual.
12. Check all gas control valves and pipe connections for leaks.
W WA AR RN NIIN NG G
C Co om mb bu ussttiib blle e M Ma atte erriia allss!!
F Fa aiillu urre e tto o m ma aiin ntta aiin n p prro op pe err cclle ea arra an ncce e b be ettw we ee en n tth he e u un niitt a an nd d cco om mb bu ussttiib blle e m ma atte erriia allss cco ou ulld d
cca au usse e a a ffiirre e w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y o orr p prro op pe errtty y d da am ma ag ge e..
R Re effe err tto o u un niitt n na am me ep plla atte e a an nd d iin nsstta alllla attiio on n iin nssttrru uccttiio on nss ffo orr p prro op pe err cclle ea arra an ncce ess..
13. Check the operation of the duct furnace gas valve by lowering the setting of the thermostat,
stopping the operation of the duct furnace. The duct furnace gas valve should close,
extinguishing the pilot and main burner flames.
14. Inspect and service the blower section of the system.
15. Inspect and check the operational functions of all safety devices equipped with your unit to
ensure that all devices are performing adequately.
High Limit and/or Safety Limit Maintenance
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e a an nd d G Ga ass!!
F Fa aiillu urre e tto o ttu urrn n o offff g ga ass o orr d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n a an n e ex xp pllo ossiio on n
o orr e elle eccttrro occu uttiio on n w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
T Tu urrn n o offff tth he e g ga ass ssu up pp plly y a an nd d d diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e d diisscco on nn ne eccttss,,
b be effo orre e sse errv viicciin ng g tth he e u un niitt.. F Fo ollllo ow w p prro op pe err llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an n n no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d..
To service or replace high limit and/or safety limit:
1. Turnoff the manual gas valve and electrical power to the unit.
2. To service the High Limit:
a. Remove the Mounting Cover located on the access side of the unit toward the rear (Air
Inlet) of the furnace section. Remove the mounting plate from the side panel of the heat
exchanger. The mounting plate is part of the High Limit; making note of wire locations for
reconnecting.
b. Remove all electrical connections from the High Limit; making note of wire locations for
reconnecting.
c. Reassemble the High Limit by replacing all parts in order; making sure the High Limit is
making proper surface contact when installed.
3. To service the Safety Limit:
a. Remove Mounting Cover located on the access side of the unit toward the front (Air
Outlet) of the furnace section.
b. Remove all electrical connections from the Safety Limit; making note of wire locations for
reconnecting.
c. Reassemble the Safety Limit by replacing all parts in order; making sure the Safety Limit
is making proper surface contact with the side of the heat exchanger.
M Ma aiin ntte en na an ncce e